New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Nice day for ploughing

Posts

Nice day for ploughing

#1

Nice day for ploughing

Wiley Horne--So. Calif.

Almost ready for first fit-up of desk project. This morning I cut rebates in the inside edges of the drawer box sides and back. These rebates are cut on the upper and lower inside edges, and will make two ledges all the way around the inner case, into which will nestle the upper and lower webs which define the drawer box.

http://www.flickr.com/photos/78661951@N07/9730784425/in/photostream/

I really like this plough plane. All boxwood. Embossed mark says 'A. Copeland, Columbus, Ohio' in three lines, with Columbus and Ohio in italic. There is pencil on top of the stock, in a very old hand like my grandmother's, "W. L. Curtis Bought of Dan M. Spencer in Milan, Ohio 1843, $9"

There is a bit of a mystery about A. Copeland. AWP, 4th Ed. says as follows: 'A. Copeland was a Columbus, OH, planemaker, whose working period is not known. If A Copeland is Alfred Copeland (b. 1802 in CT, d. 1858), the dates are between the demise of M. & A. Copeland in 1831 and Alfred's listing in the 1850 census, as a bedstead manufacturer in Chester, MA...."

Now, do you suppose that the old script on top of my plane is real? Look's pretty convincing to me, having seen my grandmother's handwriting many times. If 1843 is real, then maybe 'A. Copeland' is indeed Alfred Copeland--it's consistent with the story, though not proof of course.

The plane's fence is attached to the arms with rivets (not screws), which speaks for a fairly old dating.

I probably should've used a filletster to make those rebates. Would have been simpler. But what I like about handtool work is this plough--it connects me to other times and places as I work in the morning sun. Roughed in the rebates with the plough, and cleaned them up with a large shoulder plane. I like to think about what it must have been like back in the day, back and forth between CT and OH, starting businesses, hiring hands, making these great products.

Before the railroads were built east to west in the 1850's, it was the heyday of Great Lakes shipping and the Erie Canal, getting produce and goods from the midwest to NYC via the Erie Canal and Hudson River. In those days, Milan Ohio was the second largest grain-shipping port in the world, the largest being Odessa, Russia. Bunch of industrious guys managed to float a bond issue in the early 1830s to construct the Milan Canal connecting Milan to Lake Erie, and making it a major shipping head. An extensive loading facility was built so that the farmers and manufacturers could get their wagons in, offloaded, and out expeditiously. Bustling place before the railroads were built.

Wiley

Re: Nice day for ploughing

#2

Re: Nice day for ploughing

Bob Hackett

One of the reasons I collect and use old tools is to connect to that chain of energy and intent that runs (and hopefully will continue to run) through all the sets of hands who held and worked with these tools. Some of my favorites may not be the most desirable to collectors but they are beyond value to me because I knew at least one of the people who made their living using them. I`m reminded of my friends/ mentors/ fellow craftsmen every time I pick one of these tools up. I imagine they felt that same connection with past owners/craftsmen when they used them in their own work.

Re: Nice day for ploughing

#3

Re: Nice day for ploughing

Paul Dzioba

Hi Wiley,

Nice plane! I have a jointer plane that is special to me. I get a kick every time I use it. There is an inscription written in pencil on the back of the wedge that says "Bought by Shirief Geo Warren 1855 at Wethersfield State Prison for $1.00". Wethersfield was modeled after Auburn State Prison where they used prison labor to build planes. I bought it in Maine while on vacation.

Regards,

Paul Dzioba

Re: Nice day for ploughing

#4

Re: Nice day for ploughing

Steve Voigt

Wiley,

I seem to recall another thread where you talked about using a wedge-arm plow; maybe it was a C & W/Old Street? Anyway, any thoughts on what you prefer, screw arm vs. wedge arm vs. whatever?

One of my back burner projects is to build a plow, and I'm leaning toward a Yankee-style with screw-locked arms, but haven't decided for sure.

Of course, if any of the other assembled literati have thoughts on their preferred variant of plow, I'd love to hear. Sorry if this is a bit OT.

-Steve

P.S. Enjoyed the cool historical info!

Re: Nice day for ploughing

#5

Plough planes--my thoughts (Long, Opinionated)

Wiley Horne--So. Calif.

Hi Steve and all,

Not OT at all, and I hope to hear from others on this question!

It's hard for me to pick an absolute favorite plough, because they all work and do their job. I see numerous tradeoffs among the different styles; to get one thing, you give up another.

Metal vs. wood. Metal ploughs are compact and dense. I doubt they're heavier than some wooden models, but their weight is concentrated in line behind the iron, and they give a sense of power because of that. But wood gives me a warm, fuzzy feeling, so I prefer wood.

Iron width, nominal sizes. A new metal plough, or any new plough, will have irons with accurate nominal sizing. They'll start at 1/8", because the skate will be about 1/16", and the iron has to have room for the V-shaped locating groove, plus clear the skate on the sides with a little to spare. A new No. 3 plough iron will be 1/4" to a close tolerance. Now vintage irons are marked numbers 1 through 8, and vaguely follow a progression 1/8 to 1/2 in sixteenths, and then a 5/8". However, vintage irons will vary, and you will rarely get a vintage iron that mic's to a nominal value. A group of No. 3 vintage irons will tend to vary +/- 1/32" on either side of 1/4".

I don't find that a problem. It's like mortise chisels. You plough the groove or chop the mortise to a likely size for the situation--doesn't matter what it measures--and then plane the tongue or saw the tenon to match. Yes, there is the argument that chisels and plough irons need to match, so that you can line up the groove with the mortise (or even use the groove sidewalls to frame the mortise) when making a frame for a panel. But that is an unnecessary restriction and sometimes unwanted: You may at times want the M&T centered in the frame, but the panel groove or rebate offset from the M&T, in order to get a particular look. Krenov, for example, talked about setting glass closer to the frame face to get a sense of lightness. Or you may want a molding whose depth doesn't line up with the M&T. Hayward says to cut the mortise first: if you do that, you can locate the groove or the rebate where you want it to achieve a certain look. Of course, if it doesn't matter, then it's an easier marking situation to line up the M&T with the groove or rebate, but I don't think it's a good dependency to build because it restricts what you can do.

[NB: I'd rather have more sizes and a closer gradation than exact nominal sizes. I've recently been in the process of tenoning case sides and back and front rails into 1-5/8" leg posts (for a light desk). When you do that, you become acutely aware that you're taking a lot of meat out of the leg post to make mortises and dovetail sockets. It makes you think hard about mortise widths. I happen to have a 0.205" mortise chisel (made by mistake by the Japanese smith trying to correlate his bu measure with what I was asking for). Well, no matter. That chisel was perfect for the slightly narrow mortises I wanted to make for the multiple tenons on the side and back plates. I preferred it to the 1/4" one.]

Iron taper. If you make a plough and plan to use vintage irons, get the irons first. And get them in a true set, not a 'harlequin set', where every iron potentially has a different taper. You want them to all have the same taper, so that you can make one wedge that fits them all.

Wedge-arm, screw-arm, Yankee type--handled, unhandled. There are tradeoffs. Weight and size is one. That Clark & Williams/Old Street plough is wonderfully light and nimble--nothing there that doesn't have to be there. One of the arm wedges also wedges the depth stop in the same motion as locking up the arm. A screw-arm plough will always be heavier and bulkier than a wedge-arm plough--I think that can be flatly said without much qualification. Particularly the American screw-arms--British ones tend to have shorter arms (which is a better feature IMO). The nuts and washers add to the bulk, and then sometimes they are handled, and you can have quite a big, bulky plane. I personally don't like handled models (though they cost more originally, and have a lot more work in them), because the handle is too far away from the cutting--it feels to me like remote control. I'd rather have my hands right over the cutting, and have my hands surrounding the plane and controlling it, rather than having the feeling the plane is beyond my control, or too big and bulky to really get hold of.

One other thing about the screw arms: I've seen a number of them that restrict how close you can place your groove to the edge. Maybe the threading didn't get cut close enough to the arm hangers, or the inboard nuts are too fat, but you put in the No. 1 iron and maybe you can't get closer than 1/4" to the edge of what you want to groove. That's a problem. Yeah, you can shim the plane's fence, but that's a hassle you don't want. That problem almost can't happen with a wedge-arm or Yankee type.

Here is one thing about the screw-arms I really like--they're idiot proof in a way. Something I need. Once you lock in a setting, it stays that way until you change it on purpose. You can't knock your setting loose while ham-fistedly removing a blade for sharpening, or inadvertently knocking the arms against something. You can even set that plane aside til the job is finished, so you have that setting 'saved'.

There is a second thing, too. These screw arms represent a phenomenon that I suppose arises in a craftsman's world--the desire to make a thing better and more beautiful than it needs to be. America used to have that. As I said in a recent post, I enjoy that historical connection with an American past, and for that reason, I often reach for the screw-arm plough rather than the C&W, even though the C&W is technically unequalled and I place a very high value on having a plane made by Larry Williams or Don McConnell, both legends in their own time.

I had a really good example of a Union Factory 'Yankee' type plane. I put it up for Benefit Auction a year and a half ago, but not because I didn't really like it. I let it go because I could offer it to the group without apologies. It is a superb plane. Here is that plane:

Plough Plane with Irons

This type can be made light if you want. This particular model was a bit heavy, because Union Factory plated the fence with steel. If you make one of these, you'll want to either put load-spreading pads under the fence-locking screws, or else inlay the upper surface of the arms with something hard--brass, rosewood, persimmon, lignum vitae for example.

Wiley

Re: Nice day for ploughing

#6

Re: Plough planes--my thoughts (Long, Opinionated)

Steve Voigt

Thanks for all the info, Wiley. Your link to the Yankee plow doesn't seem to be working; I'd love to see it when you get the chance.

About the only concern I have about the Yankee style is the possibility of the fence slipping. Did you find that to be the case?

I've already got a nice set of irons, so no worries there. You're right about harlequin sets though--I found that out the hard way! Fortunately I was dealing with a reputable and honest dealer who took the irons back.

-Steve

Re: Nice day for ploughing

#7

Re: Nice day for ploughing

Derek Cohen (in Perth, Australia)

Hi Steve and Wiley

Using a plough plane that is well set up is one of the joys of building with hand tools. Conversely, a plough that has an out-of-square fence is enough to create sufficient doubts in one's ability that retiring from woodworking is never far away!

I have just two working plough planes (another lives on a shelf, but that is another story), and both of these are exceptional planes - yet so obviously different from one another.

I built a bridle plough plane about a year ago, inspired by the creations of Barrett and Sons. Here is their version ...


... and an early Mathieson, upon which it was based ...


The wonderful bridle enables the fence to be set up square and solid both quickly and reliably, unlike any other wooden plough plane fence. It is a case of twist the one knob to loosen, slide to desired position, retighten .. and you are set. No issues with aligning the front and rear of the fence.

The tapered irons are thick and solid, a little finicky to set up as the front of the skate must be aligned in a groove at the rear of the iron ..


This is a fairly heavy plane. It gathers momentum and you then discover why it is call a "plough" - it steams through the wood as if nothing can stand in its way. In its wake is a perfect groove.

My plane and build is here: http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild.html

The total experiential contrast may be found in the Veritas Small Plow.


My main criticism of this plane is the spelling! :)

I also believe that many will not have discovered its potential if they are using it without a deep sub-fence, as in the picture above.

This is a small and light plane and akin to using a scalpel to slice. The blades are 1/8" thick and small (by comparison to a woodie), and anything less than sharp will cause one to struggle. In use it offers much feedback and you feel you are driving a nimble sportscar with a tuned suspension. The high fence ensures vertical at all times - makes this a simple process. This metal plane has a superior adjuster that enable blades to be set up quickly. I have used un-handled ploughs (see - that is how it is spelled!) and much prefer a handled type for the extra ease of pushing. Both the Bridle and the Small have comfort and control. The lightness of the Small means that you need to be more watchful and paying more attention to what you are doing as it carries far less authority into a cut.

Two alternatives. Hope this was helpful.

Regards from Perth

Derek

Re: Nice day for ploughing

#8

my thoughts--RETRY LINK

Wiley Horne--So. Calif.

Let's see if this link to the Union Factory 'Yankee' plough works:

http://www.woodcentral.com/woodworking/forum/auctions.pl/page/10/md/read/id/4058/sbj/plough-plane-with-irons/

There was never a concern about the fence slipping on this plane. The wooden screws do not have a flimsy or makeshift feel. They get a firm bite without applying a lot of pressure. You do have to take care not to dent the arms because the screw has a lot of leverage, but this is straightforward using either method I mentioned.

Wiley

Re: Nice day for ploughing

#9

Subfence

Kevin Adams

Hi Derek,

What's the approx thickness of your fence...looks hefty, maybe 3/4"? I haven't tried one yet, but was thinking more like 1/2" or is thicker just that much stiffer? Do you have different sizes, maybe something even wider (top to bottom) to provide even better registration?

Thanks and hope all is well!

Kevin

Re: Nice day for ploughing

#10

Re: Subfence

Derek Cohen (in Perth, Australia)

Hi Kevin

The dimension of the subfence I use is: 9 1/4" long x 1 1/2" deep x 5/8" thick. (the original fence is 7 1/4" long x 1/2" deep).

The subfence on my LV Skew Rabbet (Rebate!) plane is similar: 9 1/4" long x 1 1/2" deep x 3/4" thick.


Nothing magical about these dimensions. I just grabbed a piece of scrap that looked reasonable. It worked so well that I kept the dimension. Even made a panel raising fence in this size ..


link: http://www.inthewoodshop.com/Furniture/Raisingapanel.html

Regards from Perth

Derek

Re: Nice day for ploughing

#11

Thanks, Derek!


Re: Nice day for ploughing

#12

Re: Nice day for ploughing

Steve Voigt

Hi Derek,

Very helpful, as always. Interesting to see your preference for handles vs. Wiley's…maybe it's just a matter of preference, like plow vs. plough? ;)

(sorry, couldn't resist. I have no dog in that fight)

I've read through your description of building the bridle plough many times--what a valuable resource. It's very inspiring…but it might be biting off more than I can chew. I think I'll start with something simpler.

You bring up a good point about about out-of-square fences. A few months ago, I made the little grooving plane below, with a moving fillister-style fence. I thought that the lack of built-in squareness would bother me, but I think I've made my peace with it, primarily by using shims to adjust it and keep it square. Perhaps it's different on a real plough, though. Or is that plow, thow? ;)


Re: Nice day for ploughing

#13

Re: my thoughts--RETRY LINK

Steve Voigt

Wiley,

What a gorgeous plane. It must have been painful to let that go. Somebody got a great deal, though.

Re: Nice day for ploughing

#14

Re: Nice day for ploughing

Patrick Gibbons

Derek, you write, "I also believe that many will not have discovered its potential if they are using it without a deep sub-fence..." What potential will I discover if I use a deep sub-fence with my plow? Excuse me, plough.

Re: Nice day for ploughing

#15

Re: Nice day for ploughing

Derek Cohen (in Perth, Australia)

Hi Patrick

Two things: the first is how effortless it is to plough vertical-sided grooves; and the second is to increase one's spelling vocabulary :)

Seriously, without a deeper fence it is possible to plough square, but it is difficult to judge the vertical for accuracy. I recall Alf writing up a tip (for the Record #044) where a long dowel was attached to the front of the plane as a guide for vertical. Nothing like that is needed when you have an assured reference to the side of the board.

Regards from Perth

Derek

Re: Nice day for ploughing

#16

Question for Derek about the two ploughs

Wiley Horne--So. Calif.

Hi Derek and all,

Thanks! Two highlights of the last few years were Kyle Barrett's winning the tool contest with the bridle plough, and then your documented experience and details of how to make one for oneself.

My question: You have a roughly 1/4" x 1/4" groove to plough--which of the two ploughs would you reach for?

Wiley ... who actually wants to know

Re: Nice day for ploughing

#17

Re: Question for Derek about the two ploughs

Derek Cohen (in Perth, Australia)

Hi Wiley

In all truth, it is more emotional than cerebral. I could have said that the Bridle is better on harder woods, but they are all hard woods. I would choose the LV for narrow boards as it is compact. It is telling that I wrote earlier that I only have two working ploughs - forgetting that I have a #043 as well, which cuts well. However it does not have a subfence and is finicky with the blade adjustment. So for small work I would use the LV. The Bridle may get pulled out less often, just because the LV is closer to hand. And then I decide today I will use woodies only, and the Bridle is the preferred tool.

Hardly scientific.

Regards from Perth

Derek

Re: Nice day for ploughing

#18

Re: Nice day for ploughing

Wiley Horne--So. Calif.

Hi Paul,

Great story! I wonder if the shirief got a good deal, considerin his position doncha know.

Can you show a picture of this jointer? How long? Blade width?

Wiley

Re: Nice day for ploughing

#19

Re: Nice day for ploughing

Wiley Horne--So. Calif.

Bob,

Do you have a particular favorite? Do you know why, or is it just the one you pick up? I ask this because I don't always know which plane or saw or chisel I will like--I find out over time by reaching for it.

Wiley

Re: Nice day for ploughing

#20

Re: Nice day for ploughing

Bob Hackett

I find there is usually a difference between a favorite and the "best" tool for the job. Many times I will use a tool that used to belong to someone I know or knew just because I want a bit of the energy and spirit that passed between us to be imprinted or carried over into the project at hand. Use a tool often enough and it becomes like that trusted friend that you can turn to for guidance and inspiration.

Many times, without any conscious thought, I have found myself using a tool as a previous owner would rather than as I would if I followed a personal preference and the work turns out better for it. I like to believe this is because a spirit and hands more adept than mine are reaching across time or distance and using my hands to guide something they are more familiar with and sure about. When these moments happen then that particular tool is my current favorite because of the connection I feel to a friend or family member.

I am at the point now in my life where I am taking many of these "favorite" tools and passing them on to some of the folks in the next generation who will be taking my place. I explain to the recipients the story of how and why that particular tool came to me, the person who used to own it and what they meant to me and many times the projects we worked on together. I explain how I believe there is a connection or "chain of energy" that is passed from hand to hand that imprints any object used will focused skill,intent and love. I also try to steer these younger craftsmen to things like the myth, lore and legend of the connections between people such as shamans and blacksmiths or priests and temple builders. I think that is one of the functions or stories, to make and maintain connections that both reach into our past and extend into our future. If nothing else these stories and connections build an added sense of respect for a tool with history and elevate it beyond being "just another tool"that you bought to get a job done.

Many times if the person who receives one of these favored tools comes back and shows an interest in establishing a deeper connection with the spirit of the past we will go to one of the drawers or boxes in the back of my shop and select a bit of old iron there that we can resurrect together. As we bring that tool back to life I explain why I think it will be superior to most anything they can buy in a store. What they come to realize as we work to transform rust into something both useful and beautiful that fits their hand and becomes an extension of it is that skill, ability, and connection are far more important than a boatload of new tools. I like to think that years from now, after I`m gone, there will be folks out there who will stop in the middle of some project and think of me and how much they enjoyed our time together as we rebuilt,refit or refurbished the tool they are presently using.

When the time comes for them to think about handing that tool on to the next generation I believe it`ll still be in useable condition partly because someone cared enough to make me a link in that chain of energy forged by past craftsmen . In return I honor those craftsman, the craft, and the tools by lengthening that chain whenever I have the chance to help forge another link.

Re: Nice day for ploughing

#21

Re: Nice day for ploughing

Paul Dzioba

Hi Wiley,

Here is a picture of the wedge that I happened to have on my computer at work. I think the plane is 26" long with a 2-1/2" blade. I will try and take a picture tonight.


Regards,

Paul Dzioba

Re: Nice day for ploughing

#22

Re: Plough planes--my thoughts (Long, Opinionated)

Paul Dzioba

Hi Wiley,

I would like to try a Yankee type plow and perhaps build one. Until then I will have to get by with the two plows I have ;)

I use this one for the tougher stuff and larger grooves, no complaints with it:



For smaller grooves and softer stock I use this one:


http://www.record-planes.com/record-no-043-plough-plane/

It is a knock off from the Record 043. With a small wooden fence added it is a sweet little plane, surprisingly comfortable. It comes with 1/8, 3/16, and 1/4 blades.

Regards,

Paul Dzioba

Re: Nice day for ploughing

#23

Re: Plough planes--my thoughts (Long, Opinionated)

Wiley Horne--So. Calif.

Paul,

Nice job on the wedge-arm!! Is that your mark on the nose of it? What angle did you use/do you recommend for the wedges? I see ray-fleck on the arms--is it all quartered beech?

Wiley

Re: Nice day for ploughing

#24

Re: Plough planes--my thoughts (Long, Opinionated)

Paul Dzioba

Hi Wiley,

I built this way back I believe in 2006, posted to WC back then. The pictures are all gone from my old posts that are in the WC Archives, the hosting service is defunct I guess.

Here is my mark, done with individual metal stamps:



I'm not sure about the angle of the wedges. I tap the arms for adjustment and tap the wedges to lock, all gingerly of course. It is a little fiddly but holds adjustment well.

The wood is cherry and not beech. I had some left over stock that was nicely quartered and thick enough. The hardware was a lot of fun to fabricate.


Regards,

Paul Dzioba

Re: Nice day for ploughing

#25

Re: Plough planes--my thoughts (Long, Opinionated)

Wiley Horne--So. Calif.

Paul,

Holy Cow! That depth adjuster knob looked so identical to vintage ones, that I thought you must have performed a transplant!! Is the skate actually folded up top, or does it just look like it? And the screws are clocked??

Thanks for showing--I do remember the 2006 post now. Remember the wedge finial. Reminds me of one of Sandusky's finials, but something tells me you did it to your own taste and eye, just like the arm wedges.

Wiley