New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

William and Mary Bible box, as a proof of concept

Posts

William and Mary Bible box, as a proof of concept

#1

William and Mary Bible box, as a proof of concept

wilbur

Finally finished a project.


This is a William and Mary style Bible box, made from walnut, with a walnut burl veneer and walnut edge banding on the front. The sides are dovetailed together, I used snipe hinges for the lid and there's a lockset that's mortised in. The proof of concept is that this project, except for the turned feet, was done completely with Japanese tools.

I've often said that Japanese tools have much more in common with western tools than differences. This project, I think, illustrates this nicely. The only problems I had with this project in figuring out methods of work using Japanese tools was how to make the decorative elements: the profile of the molding, and the turned feet.

The original plan for this Bible box called for an ogee profile on the lid and the applied molding at the bottom. The reason this was a problem is that western decorative elements are the only things that Japanese tools are not good at replicating, mainly because Japanese woodworkers didn't have the need to make those elements, so those tools were never developed. I substituted a different profile: quarter round beads on the top and bottom of the lid and the molding. There's a Japanese plane that makes this decoration, and I used it on both sides of the lid and molding to make the profile.

As far as the feet go, there is a Japanese style of woodturning, with the tool selection tending towards hook tools, with the tool being positioned below center. Here's an example: http://youtu.be/Cc4mD8t-xOs I don't have these tools, and I'm not sure where you could get them. The lathe setup is a bit different from typical lathes that you can get in this country. Also (or conveniently), my fascination with Japanese tools doesn't extend to woodturning. In any case, this is again mainly a decorative issue, since I could have made a foot of a different design using Japanese tools.

And I'd like to point out that, yes, this project was made with hardwood. ;)

Re: William and Mary Bible box, as a proof of concept

#2

Re: William and Mary Bible box, as a proof of conc

cstanford

It's a nice box for sure. You mentioned 'original plans.' By this did you mean you were reproducing the piece? If so, what was the point of not going ahead and using the appropriate Western tools for the moldings, etc.?

Re: William and Mary Bible box, as a proof of concept

#3

Re: William and Mary Bible box, as a proof of conc

Wiley Horne--So. Calif.

Hi Wilbur and all,

The Bible box has a lot of gravitas to these eyes--it 'looks' olde, and stylish olde with the turned William and Mary feet, the stunning front, and the lock! I recall the boys helping with--well, actually doing--some of the sawn veneer gluing, and I think they will look back someday on that Bible box with deeply engraved memories of its making.

Might be just me, but I think the square ovolo (not quarter-round, please!) is the very thing you want, as opposed to the ogee. Certainly looks dignified and stylish. I'm curious whether use of the close-set double-iron technique was important to your use of all Japanese tools in making the box--final planing with a 40-degree plane can be dicey otherwise.

I think that Bible box needs a special table to sit on, such is its presence.

Wonderful project, and a great thing to have the boys in on it.

Wiley

Re: William and Mary Bible box, as a proof of concept

#4

Re: William and Mary Bible box, as a proof of conc

Tony Wilkins

Great looking box Wilbur. Would love to see the work that went into it with the Japanese tools.

Re: William and Mary Bible box, as a proof of concept

#5

Beautiful work, Wilbur! 


Re: William and Mary Bible box, as a proof of concept

#6

Re: William and Mary Bible box, as a proof of conc

Tom Colligan

Really nice craftsmanship, Wilbur. Plans? Just where would they be found? Thanks, Tom

Re: William and Mary Bible box, as a proof of concept

#7

Re: William and Mary Bible box, as a proof of conc

wilbur

I used the plans mainly as a guide for the type of joinery used at various parts of the box. For the record, it's half-blind dovetails for the front corners, through dovetails for the back corners, the bottom is nailed on with cut nails, and I used snipe hinges for the lid. The molding at the bottom was made and then nailed to the box with cut nails, with miters at the corners.

Nearly everything else was altered: the actual dimensions of the box (due to the size of the boards that I had), the choice of wood, the choice of veneers, and even the bookmatching of the horizontal edgebands. The original piece had the join off center on both the top and bottom horizontal bands.

Re: William and Mary Bible box, as a proof of concept

#8

Re: William and Mary Bible box, as a proof of conc *LINK*

wilbur

Thanks, Wiley! I really appreciate the compliment.

Using the chipbreaker mainly helped with planing the lid. There were some spots that I was getting tearout that I tamed with fine tuning the chipbreaker. Of course, I could have scraped and sanded as well, but it's good to have a variety of techniques at your disposal. And even if I didn't get perfect results with the chipbreaker, it's nice to reduce the amount of scraping/sanding to do, since I like using a plane more than a scraper or sandpaper.

I also planed away the hide glue residue on the burl after it was applied. That was a lot easier than I expected. The only problem I had was in one corner a small piece (about 2 mm diameter) of burl broke out. I used some walnut sawdust and hide glue to fill that gap. But otherwise the plane worked just fine.

My older son did learn how to hammer veneer with hot hide glue as I was making this project. More info below.


9 year old hammer veneering with hot hide glue

Re: William and Mary Bible box, as a proof of concept

#9

Re: William and Mary Bible box, as a proof of conc

wilbur

The project was based off an article by Glen Huey in the October 2009 issue of Popular Woodworking, as well as looking at some original pieces from that time period.

Re: William and Mary Bible box, as a proof of concept

#10

Re: William and Mary Bible Box Plans

William Duffield

The original, on which the design was based, which was built about 1730 in Chester County, PA, was sold at auction, and is in a private collection, so we could not examine it in person. However, there are photographs and a short description on the H. L. Chalfant Auction House website.

http://hlchalfant.com/products/walnut-william-mary-bible-box

Glen Huey's plans and build description were published in Popular Woodworking, October, 2009. You can purchase a set of plans in PDF for a couple of bucks and download them here:

http://www.shopwoodworking.com/bible-inlay-box-download

Of course, Glen sacrificed many electrons in the construction of his box. :D

Method for installing snipe hinges was documented in the Spring 2009 issue of Woodwork magazine in an article by Peter Follansbee. All the issues of Woodwork may be purchased on DVD for about $45 from American Woodworker here:

http://www.awbookstore.com/product/woodwork-magazine-22-years-DVD/best-sellers

Re: William and Mary Bible box, as a proof of concept

#11

Re: Gimmals or Snipe Bills Installation *LINK*

William Duffield

Another place to find and explanation of the installation of snipe bill hinges is on Follansbee's blog, December 14, 2011. It's free there, as opposed to buying the whole history of the Woodwork magazine.

http://pfollansbee.wordpress.com/2011/12/14/setting-gimmals-you-might-know-them-as-snipe-bills/