New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

The frugal stringing sizer

Posts

The frugal stringing sizer

#1

The frugal stringing sizer

Bill Tindall, E.TN.




We made this sizer in class. The cutter is a piece of Lee Valley card stock sheared into strips and screw holes punched in it (card stock will accommodate hole punching). It is sharpened at about 45 degree bevel on end and a gentle hook rolled on the edge.

I have added two modifications. First I drove the blade down into the wood so that the bottom of the blade was below the bottom of the saw kerf where the string goes. (Driving it down makes a channel for the blade to slide in. Second, I added a hole at the end of the blade. With the blade snug, a marking point is stuck in here and the blade precisely pried closed to get the desired thickness of cut. (It is fiddly getting the blade adjusted with the screws loose.)

Re: The frugal stringing sizer

#2

Re: The frugal stringing sizer

David Charlesworth

Bill,

Where does one get such a hole punch please?

David Charlesworth

Re: The frugal stringing sizer

#3

Re: The frugal stringing sizer

Bill Tindall, E.TN.


This one is 8" and barely adequate for 0.032" scraper stock. The 12" would be better. Those in the US try Harbor Freight or MSC, Travers, Enco, etc.

Re: The frugal stringing sizer

#4

David Barnett

(Message Deleted by Poster)


Re: The frugal stringing sizer

#5

Thank you. NM


Re: The frugal stringing sizer

#6

One problem with them though...

John in NM

You get so totally spoiled! :D :D :D

Friend of mine had a bench mounted version that would punch up to 1/4" in 1/4" steel. Soooooo much nicer than drilling holes! I should have bought it when he moved, but I was in the middle of my own fiascos and let the opportunity pass me by.

Re: The frugal stringing sizer

#7

A trick for tempered stock

Patrick Gibbons, Katy, TX

Weygers suggested cutting the tip off a nail, chucking it in the drill press and running at high speed at the spot to drill through in tempered metal. The objective is to generate heat to draw off temper then to use a drill bit to drill the hole. Obviously a punch is much easier.

Re: The frugal stringing sizer

#8

Re: The frugal stringing sizer *LINK*

William Duffield

Did you use rock maple for the body of the sizer? It appears that the L-N version might be black cherry, which is much less durable than hard maple.

What keeps the stringing from wearing a groove in the side of the saw kerf as it is used over and over? I know you have said you don't plan on doing any more Line and Berry work, but someone like Steve Latta working in the Chester County, or Federal Period styles, who makes lots of stringing, might wear one out in short order.

I've noted that the one Steve and L-N designed and that L-N sells has two scraper blades and two slots. Did Steve give you any idea why one might want two slots (other than it might last twice as long)?

Would a brass or lignum vitae, Guaiacum officinale, insert in the side of the kerf make sense?

The commercially available model is also designed to clamp to the top of a bench using an F-clamp. Do you find that the addition of a hole through the body for this purpose is superfluous? I realize it would be even easier to clamp it in any vise you had at hand, unless you are working somewhere that you don't have a vise, or your vise is in use for something else while you are sizing the stringing?

I like your micro-adjuster. Since you have a punch, you could punch an additional hole in the scratch stock, over the adjuster hole in the base, and then adjust the width in either direction, open or close.


img

Lie-Nielsen Inlay Tools

Re: The frugal stringing sizer

#9

so many questions, most not an issue

Bill Tindall, E.TN.

Did you use rock maple for the body of the sizer?....yes

It appears that the L-N version might be black cherry....no, maple

What keeps the stringing from wearing a groove in the side of the saw kerf as it is used over and over?...... I suppose it will after a few thousand feet of stringing are pulled through it. Then make another. Might take 10 min to do so.

someone like Steve Latta might wear one out in short order...... Apparently not. We pulled about 100' through Steve's during class and I didn't see it suffered.

I've noted that the one Steve and L-N designed and that L-N sells has two scraper blades and two slots.....two sizes. My smart assed remark to this question in class was that "it made one feel better about paying so much for it".

Would a brass or lignum vitae, Guaiacum officinale, insert in the side of the kerf make sense? ....only to a tool builder, not to a woodworker

Do you find that the addition of a hole through the body for this purpose is superfluous?.......not if you lack a vise. Again helps justify the price.

you could punch an additional hole in the scratch stock, over the adjuster hole in the base, .....I like that idea but I probably couldn't get the hole located well enough to work.

Re: The frugal stringing sizer

#10

Re: so many questions, most not an issue

Tony-Memphis

I made one too. I used regular old maple. I like the hole so my vise is free to hold other things while I'm working. I have enjoyed Steve's DVD's. I'd like to take a class from him. I appreciate his approach to things (not too fussy).

Tony - here on the other end of TN

Re: The frugal stringing sizer

#11

spot on

Bill Tindall, E.TN.

Like most professionals he is into getting the job done as easily, cheaply and reliably as possible. Hence, if one's goals are similar it is easy to simply accept what he recommends and get on with it. We will likely have him here for a club class in the next year.

You are welcome to come visit. We hope to have Will Neptune this spring- a like minded person. You have my email. On the other hand a map will reveal that I am closer to Windsor Ontario than Memphis.

Re: The frugal stringing sizer

#12

Re: so many questions, most not an issue

William Duffield

two sizes

So you can pull it through the fatter one first, and then the thinner one? Or are there patterns that require two different thicknesses of stringing?

it made one feel better about paying so much for it

LOL! I guess there are marketing reasons for trying to provide a "total solution".

only to a tool builder, not to a woodworker

Why can't one be both, or at least aspire to both? (After all, all tools are kits.)

I probably couldn't get the hole located well enough to work

I guess the only recourse would be a threaded depth adjuster. :) And, to justify the price of that, a vernier scale… :D and brass knurled adjusting knobs… I think I need to talk to John Economaki (or the Economaki wannabes at Woodpeckers) about this one.

not if you lack a vise. Again helps justify the price.

The clamp hole in the commercial version doesn't look like it's wide enough to accommodate a Gramercy holdfast. I would think that would be more convenient than a clamp.

Tongue planted firmly i cheek. I think yours will work just fine.

Re: The frugal stringing sizer

#13

Robert Tutsky

Re: The frugal stringing sizer

Robert Tutsky

Hi Bill. I wanted to my hand at stringing so I made a few tools for the task. This what I use to cut the raw string before sizing:



The base is held in a vise, stock is held along the edge using the "cutting tool" to strip a rough sized string.

Next:

I next trim the end of the string a bit to fit through the sizer, pulling the string through to finish the sizing. The blade is adjusted to give a slight bevel to the string to easily sit into the string grove. The small block in the rear can be shimmed for the desired string height. All wood parts are maple.


Re: The frugal stringing sizer

#14

Re: The frugal stringing sizer

Bill Tindall, E.TN.

good ideas

Re: The frugal stringing sizer

#15

Re: The frugal stringing sizer

TomD

I don't know if dremels are popular over your way David, but you can cut just about any steel with them. Just touching to both sides of this card stock would make a slot between holes. We used to use them to cope 1/8" thick tubes for motorcycle frames, they will rip through enything. The glass filled ones are the best, but they are all fragile.

http://www.dremel.com/en-ca/Accessories/Pages/SubCategories.aspx?catid=2058

Looking at those options I would think we mostly used the 15/16th ones.

If you don't want to shear the steel. You can buy this feeler gage stock that comes in 1/2" Your dremel will cut it easily.

Great stock for making custom bowsaw blade, fancy a dovetail saw bowsaw in 14 thou?

http://www.victornet.com/subdepartments/Feeler-Stock/1030.html

Re: The frugal stringing sizer

#16

Re: Oh, reason not the need

TomD

http://www.frets.com/FretsPages/Museum/SpecialItems/GezaBurghardt/GezaViews/geza01.jpg

Re: The frugal stringing sizer

#17

Where can I get one.....!

Bill Tindall, E.TN.

that looks like a Bridge City Tool solution to the need for string sizing.

Actually, I recently bought a used Performax drum sander and it does a dandy job of getting the sawed veneers close. I may have paid less for it than the tool shown!

Re: The frugal stringing sizer

#18

David Barnett

(Message Deleted by Poster)


Re: The frugal stringing sizer

#19

Re: That's Geza Burghardt's purfling scraper

Bill Houghton, Sebastopol, CA

Nice recycling of a broken Stanley 78 body.