New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

liquid polyurethane glue

Posts

liquid polyurethane glue

#1

liquid polyurethane glue

eliot d

I am carefully fitting some small ( about 3/4 inch ), thin (about 1/16 inch) , end grain puzzle -like shapes into a 3/4 inch wide groove. ( they have to be end grain.) It's an inlay. I will be gluing them there and I need long setting time. I figure any water-based glue will swell the end grain pieces too much and cause problems, so I got some slow -setting Tightbond liquid polyurethane glue. (I really wanted to get a certain West epoxy product but couldn't find any.) Do you think I'll be all right with the way I plan to do it? It's a fair amount of work to do all the cutting and fitting and get everything just right, so I don't want to screw it up.

Re: liquid polyurethane glue

#2

Bad Choice!

Paul Dzioba

This glue foams as it cures and unless the pieces are clamped, the foam may push them apart. The cured foam can be a pain to clean up. I think slow set epoxy or liquid hide glue is the better choice.

The only place I have found polyurethane glue useful is to glue different types of materials like metal to wood. The polyurethane seems to stick to almost anything.

Paul Dzioba

Re: liquid polyurethane glue

#3

Agree...

John in NM

Without clamping pressure, poly glue is one big foaming mess! :D

I would consider mail ordering some long set epoxy, since you need the working time it would be best. I think Lee Valley carries a line of 2 hour epoxy.

Re: liquid polyurethane glue

#4

Re: Bad Choice!

eliot d

Say, thanks! I'm glad I asked. I did plan to use cauls and clamps. Still, I'm taking the stuff back, unopened, and get some liquid hide glue. ( So, is this stuff basically Gorilla glue?)

Re: liquid polyurethane glue

#5

Re: liquid polyurethane glue

William Duffield

I don't understand why you can't find a quality epoxy product in your area. West Marine carries West System, and Woodcraft carries System 3. They're within blocks of each other (and starting in March will be even closer, due to the Woodworker's Club's impending move) in North Bethesda. There is another West Marine in Alexandria.

As far as poly glue, I can't think of any situation where another type of adhesive would not be more appropriate, except maybe filling the desk, electronic communications devices, and pockets (or pocketbook) of your least favorite authority figure.

Re: liquid polyurethane glue

#6

Yes, gorilla glue is polyurethane glue


Re: liquid polyurethane glue

#7

Liquid hide

Wiley Horne--So. Calif.

Hi Eliot,

I've just been gluing some thin (1/8") material with liquid hide.

Main thing: Apply the glue to three surfaces--the substrate, and both sides of the thin piece you're laying down. Hitting both sides of the thin piece will equalize the hydrostatic pressure from the water, so it'll sit flat while you're laying down adjacent pieces (if any), and then while the glue dries. I'd leave it in the clamps for 24 hours in a room-temperature location, and don't remove the glue waste on top until all the visible glue dries. Why? You don't want to make one side dry while the other side is still wet. It's an easy cleanup with a smooth plane, and will not show up in the finish. This latter recommendation may be an excess of caution, but if you have a complicated glue-up using thin stuff, you don't want to chance a redo.

Wiley

Re: liquid polyurethane glue

#8

Re: liquid polyurethane glue

eliot d

I tried Woodworkers Supply on Wyacondia, Home Depot, Strohsniedrs. I need thin, watery, very slow drying glue. They didn't have it. But , you're right. I should have tried the marine stores. I think the liquid hide glue will work OK.

Re: liquid polyurethane glue

#9

Re: Liquid hide

eliot d

Thanks; I appreciate your reply. I had intended to use the glue in the dado and flood the inlays. As for planing afterwards, these inlay pieces are very thin -- and end grain ; so I may opt to hand sand this time.

Re: liquid polyurethane glue

#10

Good approach!

Wiley Horne--So. Calif.

And a wet towel for your hands, as you go along!

Wiley

Re: liquid polyurethane glue

#11

Re: liquid polyurethane glue

William Duffield

They're planning on moving from Wyaconda to 11910 Parklawn the beginning of March.

The liqid hide glue should work just fine, unless you are planning to finish with shellac and then spill hot Irish coffee on it. :\ And, you should have less problems with interactions between the hide glue and whatever finish you put over it.

If you had found the West System, you would want to use their slow hardener (206) unless you have an unheated shop. Temperature range and pot time and cure time are very clearly printed on the hardener and resin labels. Without any fillers, it is very thin. It would have done the job, but you would have found that getting started with West System, including resin and hardener and a pair of pumps, a whole lot more expensive and a lot more hassle than a bottle of Franklin's (a.k.a. TiteBond).

Re: liquid polyurethane glue

#12

Re: Liquid hide

TomD

A natural for this kind of work is cyano. Either it works when spread on the surfaces, or it works when dripped into the cracks. It is used for a ton of inlay work.

West is often available at local marine stores. They have a standard package of products that small mom and pop marines have. It might also come via ebay. Only thing is that if there is cold weather between you and your supplier, it may not be a good thing to send epoxy through the mail. I can be restored, but I prefer to buy it during warm months.

If you have coin like endgrain, epoxy may penetrate deeply, and might other glues, and show on the surface. With hide glue, or epoxy to an extent, you can size the surface, then attach with more glue. With cyano you can control the flow, or fully saturate it.

Whatever you choose, do a sample so you can examine the playground to see how well the elements play together.

Re: liquid polyurethane glue

#13

Re: liquid polyurethane glue

eliot d

So you must live near me! Do I know you from the MCW Chapter? I live in Bethesda.

Re: liquid polyurethane glue

#14

Re: liquid polyurethane glue

William Duffield

Nope, I'm in New Jersey, a half hour drive (if you know the shortcuts) SSE of NJTP Exit 1, on the Cohansey River. We used to keep an apartment in Reston, and before that in Arlington. We have friends and relatives in the DC area, and I attend SAPFM Chesapeake chapter meetings, which are often graciously hosted by the good folks at the Woodworkers Club.

Re: liquid polyurethane glue

#15

Re: liquid polyurethane glue

eliot d

So you make period furniture; that's impressive! We don't get up to NJ much, though.

Re: liquid polyurethane glue

#16

Paul Schurch uses it.

James Watriss

He's pretty much the go-to guy on marquetry, in my book.

Gorilla glue and other urethane glues can be thinned out in the microwave, which will make it easier to work with in the piece. Yes, it does expand, which can make it tricky with inlay. But the expansion will also help fill gaps.