New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

New Toy

Posts

New Toy

#1

New Toy

Kevin French

I found this drill in an antique shop today. On the collar by the wooden handle it say Goodell Brothes Co., Greenfield Mass. U.S.A., Pat. Oct. 5. 1897, but on the collar by the chuck tightener it has Goodell-Pratt, Greenfield Mass.

I haven't found a tool number for it yet.

Henry Goodell sold Goodell Brothers to the company’s treasurer and manager, William M. Pratt. I'm guessing this drill was made in 1898.


img

Re: New Toy

#2

Re: New Toy

Kevin French

By loosening the collar closest to the wooden handle puts the drill in reverse


img

Re: New Toy

#3

Re: New Toy

Kevin French

By loosening the next collar down put the drill in forward


img

Re: New Toy

#4

Re: New Toy

Kevin French

Here's a pic of the drill fully extended.


img

Re: New Toy

#5

Re: New Toy

Kevin French

With four jaw chuck removed


img

Re: New Toy

#6

Pretty cool

Bill Houghton, Sebastopol, CA

I note that the reverse threads are much slower - higher torque - than the forward threads.

I wonder why a drill needs a reverse, though? In case the bit gets stuck?

I have a tool of similar design, though I've never looked to see if it's a Goodell, the chuck of which takes a screwdriver bit. Maybe they were selling the same tool as either a push drill or a screwdriver, depending on which chuck was installed.

Re: New Toy

#7

Reverse is for removing screws.

Chuck Nickerson

Reverse has higher torque because getting screws started back out can take more force to start.

I have always loved GP quality, great find.

Re: New Toy

#8

Re: Reverse is for removing screws.

Kevin French

The problem is you can't get much of a bit in the chuck. I don't think you could get much more then a jewelers screw driver bit in it.

I had planned to use it for drilling small holes and didn't realize it had a reverse in it until I started to clean it up.

Re: New Toy

#9

Re: Reverse is for removing screws.

Bill Houghton, Sebastopol, CA

Those chucks are designed for the cruciform shanks that Goodell-Pratt (and thus Millers-Falls, and thus Craftsman/Dunlap who subcontracted their push drills from M-F) used for their push drills: four grooves around the shank that accepted the jaws. These bits are pretty rare, so you may find you've got a neat little artifact with not much real use.

Re: New Toy

#10

Re: Reverse is for removing screws.

Kevin French

Thanks Bill, it won't the first time, or last, I had a "neat little artifact with not much real use."

Re: New Toy

#11

Re: New Toy: more info

Kevin French

Spiral Screwdriver

Hardwood handle; design with two telescoping spirals locks and turns to the left or right; spirals are adjusted tightening one of two control nuts; screw-type chuck; bright parts are nickel plated; shipped with three screwdriver bits.

Inner spiral used for driving screws, outer spiral for withdrawing them.

Model No. No. 22

Length: 16 1/2 inches (no bit, one spiral extended) 9 inches (no bit, closed)

Type: paired single spirals

Start Date/End Date

1896/1930

Re: New Toy

#12

Re: Reverse is for removing screws.

Chuck Nickerson

Based on Bill's description (I haven't seen one), once you have one for a pattern you should be able to make your own.

Re: New Toy

#13

Re: New Toy: more info

Dave T

I own one of these and I too bought it without knowing about the reverse spiral.

Mine did not come with a cruciform chuck but with a single large flat screwdriver bit. The end of the shaft has two opposed flats, and the threaded 'chuck' just clamps down on the shaft. I've never found any other bits with the same shaft-end configuration, but an shaft of the correct diameter could be modified, including one with a hex holder for modern bits.