New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Why didn't I think of this years ago?

Posts

Why didn't I think of this years ago?

#1

Why didn't I think of this years ago?

Ron Harper

Lots of talk lately on the net about grinding both hand and otherwise. Ok you build a nice little tool rest for your hand grinder, or if you are fortunate you have one for your grinder. How does one keep the bevel uniform? We see pics of wondrously talented galoots doing this freehand. I ain't that good. Many of us have the eclipse style "training wheel" honing guide. Very effective when held against the tool rest on my grinder. Allows me to grind a uniform bevel on chisels and plane irons. Why didn't you tell me this years ago?

Ron a Kokomo Galoot who honed a bunch of stuff today.

Sent from Xfinity Connect

Re: Why didn't I think of this years ago?

#2

What am I missing?

Tony (Charleston, WV)

I'm sure I'll give myself a head slap when you answer, but how do you get the jig to slide back and forth so you can pass a chisel across the face of the wheel?

Thanks,

Tony

Re: Why didn't I think of this years ago?

#3

Re: Why didn't I think of this years ago?

Derek Cohen (in Perth, Australia)

Hi Ron

Generally one just uses pinched fingers as a fence (against the rear edge of the tool rest) to limit the depth of grind (as so keep the grind on the bevel even). However you could also use the chip breaker (screwed to the blade) as a depth gauge, as you are no doubt doing so with the Eclipse.

Regards from Perth

Derek

Re: Why didn't I think of this years ago?

#4

I will try that

Ron Harper

I have tried lots of " freehand" strategies. I will try some more, but right now the Eclipse serves as an almost idiot proof helper

Re: Why didn't I think of this years ago?

#5

Re: What am I missing?

Ron Harper

Front bar of eclipse registers against back of tool rest

Re: Why didn't I think of this years ago?

#6

Re: Why didn't I think of this years ago?

Chuck Nickerson

TLN has a page on this in his book on sharpening.

He sets two pins in the jig to ride a bar or pipe or whatever.

When I saw it, the hair went up on the back of my neck.

15 minutes in the shop and the Eclipse is good for all my grinders.

Re: Why didn't I think of this years ago?

#7

Needs practice

Ron Harper

I figured out how to use the middle finger as a gauge while pinching the iron between the thumb and index finder. With a hand grinder it is challenging to keep the edge tight against the wheel.

Re: Why didn't I think of this years ago?

#8

Duh!


Re: Why didn't I think of this years ago?

#9

Re: Why didn't I think of this years ago?

TomD

If you are talking about grinding straight bevels as on chisels and plane blades of the simple type, it is really easy. The pinch does not guarantee results, but it is an anchor, or reference, and helps. Depends whether we are talking tool making, where one starts from a blank, or grinding a formed bevel. I assume the latter. In which case the basic skill required it to learn to float the tool on the wheel. This is a basic part of all power grinding, for me. It involves with the wheel spinning, delicately positioning the bevel so it matches the wheel, or if the bevel is flat, say, and the wheel convex, getting it spinning in the correct relationship on the wheel.

The floating is having contact, where probably some very small amount of grinding is occurring, the wheel is spinning, the correct relationship between tool and grinder is being observed (or one thinks it is). The reason this is important, is because to go from floating to heavy grinding requires little more than pressure. If you simply whack the tool onto the wheel, you have less reference than if you find the groove through floating first. I'd say there probably aren't sparks when you are floating, or not many. You could heat the tool a little, so probably best to get on with it.

Once you apply the pressure, get the blade moving back and forth across the face of the wheel. This should be done with the legs. Keep the arms tucked and supported, they clamp the blade in reference to the body.

After you have ground a little check to see if you are making the right marks. If not, make an adjustment, float it traverse it, check it.

Grinding is basically just turning in reverse. You use the spinning thing to shape the tool. Making a straight cylinder on a lathe, is not one of the harder things to do. Almost anyone can do it. Grinding a straight bevel is what you would get if it turned out you weren't cutting a straight cylinder but rather you were all along sharpening the straight bevel on the wheel.

Re: Why didn't I think of this years ago?

#10

Hand grinder?