New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

What is the most useful thing learned from WC?

Posts

What is the most useful thing learned from WC?

#1

What is the most useful thing learned from WC?

Bill Tindall


This is an easy question for me to answer. It is the use of a shooting board.

I use machines when ever possible. But for fitting nothing beats the precise control one has from the hand tool removal of wood, one shaving at a time. Today I am fitting drawer fronts. The ends are "shot" to get a perfect reveal at the ends. Perfection is simply a matter of patience when one is sneaking up on the perfect fit by 0.003" increments on the shooting board. One would have to be exceptionally skillful to accomplish the task with the table saw.

Before the drawers it was shooting miters to get a perfect coming together of the molding. And then it will be shooting to fit the "darts" at the ends of the "dromedary" double humped molding that is applied to the front of typical Chester Co furniture.

I don't remember who introduced me to shooting boards but to them I am eternally grateful.

When these drawer fronts are fit I will get into evaluating the new Lee Valley steel chisel for dovetailing- tomorrow I hope.

Re: What is the most useful thing learned from WC?

#2

Ellis Walentine

...And another discussion...

Ellis Walentine

...re your chest in process...

The topic is fitting a drawer front here and now. How much smaller than the carcase opening do you shoot for at this stage, and how do you take anticipated shrinkage/expansion into account?

Nice post. I agree that shooting boards are a well-kept secret.

Ellis

Re: What is the most useful thing learned from WC?

#3

Re: ...And another discussion...

TomD

Shooting boards? I would have thought that next to articles on benches, articles on novel shooting board type, particularly online would be a close second. OK, probably articles related to dovetails, and articles related to plane reconditioning would be in there.

I think loose diamond sharpening might be one thing I learned about here, and now use. I argued against a lot of the overselling and so forth, but never doubted the idea it could be useful as soon as I could actually get the diamond paste into my hands. I still use other methods though.

Re: What is the most useful thing learned from WC?

#4

Re: Or to flip it,

TomD

what is the thing you know that you feel you have never been able to get across in all the posts you have here? I have a few things on my list, and I think I know a few tendencies out there. But I wonder what some of the folks who don't post so much here feel we drop time and again.

Re: What is the most useful thing learned from WC?

#5

Re: Or to flip it,

William Duffield

I think the most useful thing I've learned recently is how a chip breaker really works. And the most frustrating thing is how few people grasped the essence of what was being posted. Everyone seemed to want a cookbook number for how close to set the breaker, and totally ignored that it was strongly dependent on the elasticity of the particular piece of wood being planed, not to mention the angle of the blade and the relative angle of the blade and the front of the breaker, and that it was easy enough to determine when you had it right without ever making a measurement with a silly micrometer.

Re: What is the most useful thing learned from WC?

#7

Re: What is the most useful thing learned from WC?

Bob Hackett

I especially like the number of people who post here who think outside the dovetailed box. On some of the other forums I used to visit there tended to be alot of shouting that there is only one way to do something if you wanted to do it right. The tolerance and respect I find here allows ideas and techniques to be presented, heard and explored that would many times be cut off or shouted down in other places.

For me the most important tool I can own is an inquiring mind. The most important technique for the use of that tool would be to keep my mind open while engaging in critical thinking.

There has to be at least a million places you can go to in order to find answers to WWing questions. I`d rather understand something than be handed answers. Understanding requires me to engage in independent thought, experimentation, and then actually put what I`ve learned to work in the real world with some measure of success.

This is one of the few places I`ve found where knowledgeable and experienced people will take the time to explain what they`re doing in enough depth that I can understand what is actually happening. Once I understand what is happening I`m far more likely to be able to apply what I`ve learned successfully. Success is one of the most powerful motivational tools I know of. The folks here help keep me motivated and teachable. I look forward to learning a lot more from you all.

Re: What is the most useful thing learned from WC?

#8

Re: Self enforced ...courtesy of warren..

david weaver

... to stick with the second iron until i could duplicate what warren says about using a double iron.

Without a doubt.

I have used my infill smoother only one time since that discussion took place.

Re: What is the most useful thing learned from WC?

#9

shooting board adjustment

Bill Tindall


(Things are accentuated in the picture so as to be more obvious . ) I keep a stock of plastic shims. They can be handily cut from the packaging that is common. A typical plastic shim can barely be seen laying on the drawer front. Its position is simulated by the vertical stick of veneer on the back edge. By adjusting the position of the shim and/or its thickness the angle of the "shot" end can be adjusted as needed to fit the opening.

Re: What is the most useful thing learned from WC?

#10

Three things, specifically.  Well, really, four.

Bruce, a MN Galoot

1. Shooting boards have made all manner of fitting much more precise and easier to do for me.

2. Diamond on cast iron for sharpening.

3. Like David W., the realization of the critical importance of the cap iron positioning on planes. Uffda! I don't have an infill, but if I did I doubt I would be using it anymore. It's even turned my #6 into a big smoother.

4. Having a place where these types of topics can be discussed in greater detail than anyplace else without the conversation devolving into a MTBTYT argument.

Re: What is the most useful thing learned from WC?

#11

Before the discussion, I used a cookbook approach

Bruce, a MN Galoot

and just kept the chipbreaker on my #4 set between 1/16" and 1/32". It worked okay on the softer stuff and even domestic hardwoods, but didn't work worth a hoot on the African mahogany I tackled last year. That's what convinced me that there must be something faulty with my plane.

This discussion hustled me out to the shop to reset the chipbreaker and lo and behold! the damn thing worked great! Who'da thunk it was adjustable and would be so responsive? :D

Re: What is the most useful thing learned from WC?

#12

I would say that ...

Stuart Hough

the best thing I have learned is that Wood Central is the ONE place I can go to discover 1000 or more ways to tackle the problems that arise while I learn the craft. It is like a living library, where solutions evolve so I can find a new clue and discover for myself what I need to know. To paraphrase an old motocycle ad..."You find the best people here on Wood Central!"

Re: What is the most useful thing learned from WC?

#13

Two basic principles

Wiley Horne--So. Calif.

1. Sawing along two lines.

2. Edge joining by planing from the 'inside out'. This becomes an especially powerful technique for thin stuff, if you have a square plane and a flat bench. You don't need a shooting board. Plane on its side, running along the bench. Work on a flat board, to elevate it. Just work from the inside out. You can do this essentially freehand. Extremely valuable for thin joins, like drawer bottoms, dust panels, and appearance veneers (say, 3/32" to 1/8" thick) like for table and desk tops.

Wiley

Re: What is the most useful thing learned from WC?

#14

Jesper, Denmark

Re: Easy.............

Jesper, Denmark

Reading that all the mistakes I have ever made (in woodworking!) have been made before and that other people found many different methods of correcting them.

Does not make you feel less stupid at times, but at least you are in good company.

Re: What is the most useful thing learned from WC?

#15

Re: What is the most useful thing learned from WC?

Derek Cohen (in Perth, Australia)

... that there are many ways to skin a cat,

... and an equal number of opinions to go with these.

... that fixing an error is common place,

... and taking a risk with a new technique or level of difficulty is what helps one grow as a woodworker.

Regards from Perth

Derek

Re: What is the most useful thing learned from WC?

#16

Jim in Burlington Ont.

Re: Two basic principles

Jim in River Oaks, Ont.

"LIKE"

Take care,

Jim