(Message Deleted by Poster)
(Message Deleted by Poster)
Posts
Re: (Message Deleted by Poster)
#2Re: Weekend project taking all summer
Bruce McCrory
[Is this going to be strike #2? ... Post!]
I remember telling my wife they would be done over the weekend. We were going to use them this summer. Past summer--Fall weather is happening, now.

I am replacing the old set of outdoor furniture. The above pic. shows the sole remaining, almost useable chair of four. A side table could go another ten years. The above chair took its design cues from an earlier set my wife bought from a beat up truck cruisiing the neighborhoods, when our [now] 30+ son was a toddler. I spent last winter designing the latest replacements.
The first set was built from repurposed Western Red Cedar. Power-driven un-clad nails held the pieces together for about ten years. Not a few resorts in Washington and Oregon have that first design scattered about the grounds.
My rebuild (the one, above) cost $40 +/-, in 1994/5, and included a love seat, two singles, and a small side table. No finish, drywall screws, and boards picked from the fencing stacks (2x4s and sub-three quarters pickets). They could have been designed better, but served their purpose very well. 18 years ain't too shabby for raw cedar.
The current set (below) has many construction tweaks to fix the earlier oops's. And, it fell into the Adirondack style trap--they look so nice. However, unlike adirondacks which make you look like a beetle stuck on its back, sit down in these, relax, and jump out anytime your weak bladder needs a drain.

Besides the sloped seat-leg in 5/4x8 there is a 4" wedge/lift to put your tail where it wants to be. No struggling, no waving arms and legs. There's lots of room for a cuppa and paper plate too.
There are design tweaks between the two chairs. One was stretched so 300lb trolls are comfortable. They are tweaked from a first prototype. The Proto even went through evoltionary changes. Proto still needs to be built.
I am currently preservative finishing them. One has two coats of SystemThree S-1 epoxy (sealer?). Ghastly costly stuff. And, its ugly. And messy. And blobs all over. The glitter needs to be rubbed out, which will probably make it look like chalk. The second has a first coat of quarter-cut Epifanes varnish. An ungodly priced can that is only one of many, should I be insane enough to apply the spec'd. dozen, or so, coats. This is not a boat deck!
These two chairs cost more than any others we have in the house. One board was well over $40. And the stinkers at the lumber yard charge by lineal foot. I regret getting coated decking screws instead of stainless. The old chair shows streaks of iron leachate from the screws. The glue was epoxy and all but the front leg attachment include glue. Most screws needed preboring and countersinking. Even though cedar is soft, old growth from east of the Cascades Range (in drylands) will split and splatter grain.
Cedar will rot any iron fastener. I don't hold much hope for the coated screws lasting more than 20 years. Also, in the process of rotting metal, the wood deteriorates at connections and end grain. Any endgrain attachments also have face grain connections. This is why there are cleats under the front end of the arms. There is also a 2x4 behind the leg with both top and side penetration. A nail will slip out of cedar after 5 years. There are no nails.
Some of the cedar is salvaged from a deck rebuild completed in 2000. One chair has 2x2 pickets for seat slats. A couple of the 2x4 blocks are from scraps of a Redwood picnic table that was built probably over 50 years ago.
The one adirondack headache they don't fix is the massive space they occupy. And, I squished, and squished. For scale reference, the arms are 5.5" at the widest. The back slats are from 1x3, 2.5" finished to 2.25" at the crown. Seat slats are 24" wide at exposed end-grain.
So I am designing another type of chair for our cosy deck.
Re: (Message Deleted by Poster)
#3Re: We have pictures!
Re: (Message Deleted by Poster)
#4Summer isn't over for a while yet!
Re: (Message Deleted by Poster)
#5Re: Summer isn't over for a while yet!
Bruce McCrory
I know you all in the mid-west have really suffered from drought, but summer is done here, in the Puget Sound.
I'm ready for a new project, but these two chairs still need finish (per my schedule) to be completed. Night temps. in the 50s, and AM fog can turn into fog and misty rain any time.



