New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Tapered Blades

Posts

Tapered Blades

#1

Tapered Blades

TomD

I just bought two tapered blades off ebay, both Marples, one a toothing blade, and the other a scrub or severe jack type blade. What surprised me a little was how thick the blades were. Maybe it is a toothing thing where there is a requirement for even more heft due to the scoring. But from some of the stuff I had read, and some of the antique tools I had picked up, I had not expected such thick blades. What gives? Was Marple's quality better, etc... I'm still unpacking from the trip to the East, so I don't have any numbers, but hefty, 3/16" or maybe a little more.

Re: Tapered Blades

#2

Re: Tapered Blades

Brian Cameron

Tom:

It was quite common for the irons of benchplanes and many moulding planes to be thicker at the cutting edge to reduce chattering. Remember that at the time these planes were probably made most plane mfgrs imported the blades from another source, and that the same plane builder could use several sources over its history, leading to inconsistant measurements of blades re constant thickness etc.

I tend to think that when a toothed blade was called for the tapering was minimal to reduce both cost and chatter.

Best from thr North

Brian

Re: Tapered Blades

#3

Re: Tapered Blades

david weaver

I think the quality of most of the makers is similar, as is probably the hardness.

The later wooden planes and the infills with tapered irons that I've had have irons about 3/16th thickness.

I think the thinner very early irons are probably related to the cost of steel and iron since everything was hand processed. Most everything I have that looks like a bench plane is 3/16th at the bottom, even the relatively early single iron plane that I have that's somewhere in the neighborhood of 1830-1840.

If you were to find a laminated iron that was wide and only 1/8th or so, that'd be less common.

Re: Tapered Blades

#4

Tapered blades rule ...

Derek Cohen (in Perth, Australia)

... in wedged woodies.

In the thread below on diamond plates - particularly the coarse end of the spectrum - what lay at the back of my mind was the recent experience of flattening the back of a tapered blade for a jointer I was building. The iron was a Sorby, 2 1/4" wide and 3/16" thick at the business end. This is pretty much typical of he tapered blades I use in woodies. Some are even thicker. The 3" wide Berg iron I used in a coopers jointer is around 5/16" as I recall. And both these irons are laminated with extremely hard steel. They took forever to flatten on 45 micron diamond paste.

These irons are thick enough to be used sans chipbreaker. Yes, a chipbreaker could aid the ultimate performance, but this is unnecessary in these planes. I still prefer the lack of complication from a single iron plane. The advantage from a tapered iron is that, when used with a wedge, it does not slip. I do not get this level of stability from a parallel blade when using a wedge.

I hope this discussion does not lead to a rush on tapered iron on eBay! Perhaps we need to get Lee Valley to begin production of tapered irons in PM-V11! :)

Regards from Perth

Derek

Re: Tapered Blades

#5

On the list!


Re: Tapered Blades

#6

Re: On the list! Ahhh, yes!

Bruce McCrory

I keep thinking of the quarter turn warning in the literature as I put screw driver to blade lock, and snick another eighth.

Wonder if it is cheaper to mill a taper, or buy new?

Oops! Er, ... does this void my LAS warranty, now?