New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Let us talk about router technique

Posts

Let us talk about router technique

#1

Let us talk about router technique

Patrick Gibbons

This morning I was making some 8" x 3" recesses in a board to hold some diamond stones. Very shallow, less than a quarter of an inch. I was using a Stanley router with a newly sharpened plow blade. I scored the edges with a sharp knife. I had some chip out around the border outside of the recess. I always seem to have this result and it is unsightly though not structurally, a problem. Am I taking too big a shaving off? What is proper router technique?

Re: Let us talk about router technique

#2

I don't do it that way

Bill Tindall

I may be the least expert here but I never use the router plane to cut to a scribe line. I am always using it to cut the a shoulder that has been established by chiseling.

That said I used the diamond stones quite different. They are stored in a plastic bag. In use they sit on that rubbery shelf liner stuff that looks like expanded metal. After use the stone is washed with spritzes of water, dried and bagged. The shelf liner gets washed occasionally too.

I try to float the gunge off and over the sides of the stone in use. It flows harmlessly onto the shelf linger where it can be washed away later.

Re: Let us talk about router technique

#3

Re: Let us talk about router technique

Derek Cohen (in Perth, Australia)

Hi Patrick

1. Mark the circumference with a sharp knife as deeply as you can.

2. If the wood is crumbly or brittle, then score another set of lines inside the rectangle. The aim will be to work to these, then finish off by widening the mortice to the outer lines.

3. If the wood is firm, then just undercut the lines so that you still will work a little way from them.

4. Use a chisel to create a series of kerfs across the surface. Try and do this just short of the desired depth. You can create a hatch of lines. This makes it easy to remove the waste.

5. Once the waste is removed - use a wide chisel bevel down - then it is time for the router plane. In this situation, all it is doing is leveling the floor. Either take the blade carefuly to the sidewall or, better still, finish with a wide chisel.

Regards from Perth

Derek

Re: Let us talk about router technique

#4

Re: Let us talk about router technique

Patrick Gibbons

Once again being lazy and looking for shortcuts leads to substandard results. I started out using a chisel but figured that since I was cutting out less than an eighth of an inch, maybe 3/16ths, I'd just make a number of shallow cuts with the router and finish quickly. Should have stayed with the chisel. I've picked up some good tips though. Thanks for the shop secrets.

Re: Let us talk about router technique

#5

Re: Let us talk about router technique


Re: Let us talk about router technique

#6

All thumbs today

roninkokomo

I meant to say. Use a chisel for this job. Do the last little bit of flattening with the router plane.

Re: Let us talk about router technique

#7

Pictorial for critique

Derek Cohen (in Perth, Australia)

Patrick and all

As it happens, today I needed to create a shallow mortice, and the techniques involving the router plane, and where it fits in, were involved. It only dawned on me to take pictures after I had begun, and so the process starts with the marking, hatching and rough waste removal already done.

The task involved was to create a mortice for a brass mouth piece for a jointer plane. This is identical to setting a hinge mortice. (Incidentally, this is the last laminated plane I will make. With the memory of the plough plane in mind, it is more work that chopping out the bed and mouth. I had the parts, so just used them).

What you note here is that I am working within the defined boundary.


In paring out the waste, try to work across the grain to avoid tearout.


The same technique applies when using the router plane. The router's depth is set, and then reached incrementally.



By the way, I hollow grind the faces of these router blades. They are then easy to hone to razor sharp ..


I decided the V blade would work more easily into the edges. This was already set up in my shop made router, which was also smaller and easier to maneuver. Again the bevel edge is used across the grain ..


The edges of the mortice were finished by scoring with a cutting gauge ..


Left with just the front section to remove, treat it like a dovetail and undercut the line. This will ensure that the chisel does not move over the line ..



And finally the fitting tells all ..


Regards from Perth

Derek

Re: Let us talk about router technique

#8

A "trick" I learned from Krenov school

Bill Tindall

When mortising to install something brass-hinge, lock, etc- first file a tiny chamfer on the bottom edges before scribing the outline on the wood. This chamfer causes the marking knife tip to ever so slightly undersize the mortise, or at least not oversize it. The brass piece will then press fit into the mortise as though it grew there.

Ideally, the support for a hinge is provided by a tight fit of hinge to wood and the screws just keep the hinge from falling out.

Re: Let us talk about router technique

#10

Re: Another hinge mortise tip *LINK*

William Duffield

Derek,

If you can turn the blade around on your cutting gauge, it should also help you to get a tighter fit, because you'll get walls that are vertical. That's one reason I like the new Veritas dual cutting gauge. One blade is vertical towards the end of the bar, while the other blade is vertical towards the fence, and I don't need any tools to swap modes. If you are going to use it for mortises and tenons, definitely get the accessory shaft clamp.


Veritas Dual Marking Gauge

Re: Let us talk about router technique

#11

Re: Let us talk about router technique

chris hyde

Try defining the line wall with a chisel so that you are not having to cut up to the line with the router plane. I do this when cutting dadoes and I don't get breakout.

Re: Let us talk about router technique

#12

Re: Let us talk about router technique

Patrick Gibbons

I cut my second recess the right way using a sharp two inch chisel. An unrelated problem I had was caused by the chisel edge which was not at 90 degrees to the length of the chisel. It made the chisel harder to control. Things turned out better. I should have attached a larger wooden sole to the router for better register, but there was enough contact to work without problems.

Re: Let us talk about router technique

#13

Chisel size- big doesn't work for me

Bill Tindall

Huge chisels are surely made for some useful purpose but I have not discovered it while establishing the edges of mortises. While it seems logical to use a 2" chisel to establish the outline of a 3" hinge it doesn't work out that way for me. I get much better control and accuracy with the smaller chisels. I just walk the chisel down the scribe line with precise controlled tapping.

Re: Let us talk about router technique

#14

I agree but I don't understand why it is so


Re: Let us talk about router technique

#15

Re: Chisel size- big doesn't work for me

Patrick Gibbons

I find myself using the two inch chisel quite a lot. It keeps its edge well and slices through easily. To each his own.

Re: Let us talk about router technique

#16

I have two 2" Berg chisels,

Bruce, a MN Galoot

one is a typical wooden-handled biggie, with 5-6" of blade (I'm not at home and can't measure it) and a mongo-sized Karellian birch handle that's only suitable for whacking on.

The other is a plastic-handled Shark-O-Lite with a much shorter blade. The whole thing is maybe 7-8" long. It is unbelievably useful and lives on my bench -- it never gets put away as it's always at hand for duty as a scoring, paring, marking tool. I would never have thought it would be so useful but it certainly is. As a marking tool, it's great because the size of the blade registers so easily against a straight edge. I use it a lot for starting cuts like the ones in this thread.

The first chisel I ever worked with was a 1-1/4" Stanley 60. I consider this 2" Berg its natural successor.

Re: Let us talk about router technique

#17

Re: I have two 2" Berg chisels,

William Duffield

A master of the technique of using a wide chisel for a marking and cutting knife is Paul Schurch, an expert in marquetry from SoCal. His has a handle, but in general he doesn't use it when cutting up veneer.

Google "Schurch marquetry" for more info, especially if you are interested in learning the art and craft while waiting for the first volume of Roubo from Lost Art Press.