New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Sanley No. 60 chisels

Posts

Sanley No. 60 chisels

#1

Sanley No. 60 chisels

eliot d

I picked up a four piece set of these at an antique shop for about $30. They are in pretty good shape. Are they anything worth talking about?

Re: Sanley No. 60 chisels

#2

Re: Sanley No. 60 chisels

Bruce, a MN Galoot

They're some of my favorite users; they're what I grew up using. With the steel caps on the handles, I feel absolutely no qualms about whacking the daylights out of them. Last year I bought a 5/8" #60 (sans handle) and ground it down to become a fishtail chisel for paring out sockets of half-blind dovetails. It works very well. Good steel.

Re: Sanley No. 60 chisels

#3

Re: Sanley No. 60 chisels

Bill Houghton, Sebastopol, CA

In my experience, very tough steel. Foine Workwooding, years ago, was critical of them for the out-of-flatness of the backs, but this is a curable condition.

Like Bruce, I like the steel cap; they're my construction chisels, and I don't have to carry a mallet in addition to the hammer.

Re: Sanley No. 60 chisels

#4

Love my 40 s

Roninkokomo

I am not sure how the 60 s are different from the 40 s but I sure do love my 40s. As has been said, they really take a pounding. I had to rehone to 30 degrees. At 25 I was nicking edges too often.

Re: Sanley No. 60 chisels

#5

40s are longer than 60s

Bill Houghton, Sebastopol, CA

and the one 40 I own has a black plastic handle, rather than the yellow (with some black paint on some) handles of the 60s.

The 40s are good chisels, too.

Re: Sanley No. 60 chisels

#6

Jack Guzman from Maine

Re: 40s are longer than 60s

Jack Guzman from Maine

My 1 1/2" 40 with the black handle fits right in with my set of LN bench chisels. It holds an edge just as long as the LNs. Mine is the same length. Besides the handle it looks like it could be part of the set.---Jack

Re: Sanley No. 60 chisels

#8

Thanks


Re: Sanley No. 60 chisels

#9

I have an unusual Stanley chisel

Patrick Gibbons

It has a small black handle that is flat with a concavity in the middle of the handle. I'll dig it up out of the garage and see if I can take a picture. Anybody know anything about these?

Re: Sanley No. 60 chisels

#10

Re: Sanley No. 60 chisels

eliot d

Thanks. About the fishtail, what is it about he fishtail shape that makes it useful for cutting half-blind dovetails? (As you can tell, I've never done it.) Can half-blind dovetails be cut just as well (perhaps with more work) with ordinary chisels?

Re: Sanley No. 60 chisels

#11

Re: Sanley No. 60 chisels

Bruce, a MN Galoot

Well, it doesn't have to be a fishtail. You can do the same thing with a small skew chisel, too (and I have a set of Stiletto chisels that I ground into a skew profile, thanks to Bill Houghton). They're used to dig out the inside corner of the dovetail socket, and unless you have a very small chisel, say an eighth inch, those are really the only chisels that work well. Trust me, when you are faced with a half-blind dovetail socket you'll understand. All in all, though, the skew profile is more useful and less specialized.

Re: Sanley No. 60 chisels

#12

Re: Sanley No. 60 chisels

eliot d

Thanks, I can picture what you mean, even though I've not done one.( I'd better start with the "regular" dovetails, though.)

Re: Sanley No. 60 chisels

#13

Haven't found the chisel yet