New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Sticking Board questions

Posts

Sticking Board questions

#1

Sticking Board questions

William Duffield

In the past, I've hand planed quite a bit of molding, but it's usually been either replacement gingerbread in the late 30-30* style and buried in paint, or really simple (or done on a router table).

Recently, I've been watching Don McConnell's DVDs from Lie-Nielsen, reading Matt Bickford's blog, "Musings from Big Pink" and excerpts from his soon to be released book. I need better techniques, and also better tools, including a sticking board, something better than just clamping a board to my bench top to use as a fence, and another one to use as a stop.

A question to those who have a sticking board and have used it to stick moldings: What details of the design and dimensions work for you? Don McConnell uses one with a wide but not very high fence, that can be adjusted horizontally. Matt Bickford, OTOH, uses one that looks and acts like a long bench hook, with a high fence on one surface, and a lower fence on the flip side.

Of course, everyone's sticking board uses a variety of adjustable FHWSs as end stops, sometimes some at both ends, and they hold the sticking board between a dog in their end vise and a dog placed near the other end of the bench. For now, I will probably use a Veritas wonder dog at one end. I will also need to be able to plane on the board in either direction, as I'm left handed, and have a left handed rabbet plane, but my hollows and rounds are right handed.

So, is adjustable width more important, or is a board that is wide, and the fence therefore farther from the front edge of the bench (where it will give my back more grief), but with adjustable height, better or worse? Are there alternate designs that work better, or that resolve this dilemma? How long does it need to be (I don't plan on wainscoting a whole house, but you never know)? My bench is about 7' long. What is the maximum working width that you have found useful?

As far as materials, I think my choice is tulip poplar, but if that isn't appropriate, I might be convinced to use guatambu plywood or even MDF. What works best for you?

* to be viewed from 30 feet at 30 mph.

Re: Sticking Board questions

#2

Shannon Rogers

Ron in Kokomo

He has built a new one and has pics on his web sites. Might be useful to you. He also is left handed

Ron

Re: Sticking Board questions

#3

Re: Sticking Board questions

TomD

Isn't it going to turn out to vary depending on the kind of moldings you want to make? This is why I like to keep it simple, I am not a molding shop, and I can coble stuff up on my bench without having to worry about making the ultimate sticking board with the most adjustments known to man, though that could be fun also. I find since I like to take a shot at just about everything, that I like to keep it flexible.

Re: Sticking Board questions

#4

What I did *LINK*

Bill Houghton, Sebastopol, CA

I needed a sticking board a couple of years back, and made one for the occasion. I described the making in the post linked below.

Like TomD, I didn't try to make an ultimate board - just something to get me through the project.


http://www.woodcentral.com/woodworking/forum/archives_handtools.pl/bid/3001/page/1/md/read/id/151602/sbj/adjusting-small-molding-long-lots-o-pics/

Re: Sticking Board questions

#5

Re: Sticking Board questions

Warren in Lancaster, PA

I see a sticking board as a production tool. I make one if I expect to make dozens of the same moulding. I do have one that is 8 feet long. If I am making a single moulding, I can use a board I have laying around or a number of other methods. I have had to make a large variety of mouldings- hard to imagine a sticking board to cover every situation.

Here are some other methods: Make the moulding on the edge of a wider board (that you can put in the vise or clamp to the bench), then rip the moulding off the edge. Or Cut the moulding blank a little long and fasten it at both ends to a piece of pine with countersunk nails. Or Use hide glue to fasten the blank to a board to be held in a vise. Or Screw a holding board to the underside.

Re: Sticking Board questions

#6

"...then rip the moulding off the edge"

Bill Houghton, Sebastopol, CA

It's occurred to me more than once that this process, if done with hand tools, might require a sticking board to clean up the ripped edge; although, if I were a better sawyer, that might not be so.

Re: Sticking Board questions

#7

Re: "...then rip the moulding off the edge"

Warren in Lancaster, PA

The sawn edge is cleaned up with a plane, one way or another. I usually lay out gauge lines for sawing on both sides of the board before doing any moulding (while I still have flat and square surfaces). The method for planing the back of the moulding depends on the peculiarities of the moulding.

Re: Sticking Board questions

#8

Re: Sticking Board questions

William Duffield

Thanks for all the ideas, guys, especially the warnings that "one size fits all" probably doesn't work. What I am hoping for is a board I can hang on the wall when I'm not using it, and drop it onto the bench when I need it. I'm tired of over-designing things, but having to reinvent a fixture and find the right pieces of scrap to build it every time I need it is even more frustrating.

I think I have an idea that will allow me to build a bit of modularity into my board, and still have the stability I need. I'll let you know if it works. Heck, I'll even let you know if it doesn't work. For now, I'll call the concept my "Lego" sticking board. It's based on some ideas I used when I made some modular push sticks with sacrificial parts.