New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Infill cap iron questions *PICS*

Posts

Infill cap iron questions *PICS*

#1

Infill cap iron questions *PICS*

Dave Thompson

I haven't been around in a while, but it's nice to come back and see so many familiar names. I had some questions about some infills that I recently bought that I was hoping you might be able to help out with. I wasn't really in the market for these, but someone local was looking to unload them, and so I helped him out.

So the first I have a question about is an open tote Spiers which I think is called a #7. It came with a 3/16" thick Hock blade and an appropriate vintage (looking) Sorby cap iron with a bronze bolt receiver. At first, I thought it just need the cap iron screw, though now I'm not so sure this cap iron is even going to work, as the bronze bolt receiver (nut if you will) protrude above the cap iron and will not fit under the lever cap. I'd be interested in your opinions whether I just need to find a new cap iron or other, or whether I should attempt to grind the bronze "nut" protrusion on the cap iron. I'd rather not do that as it looks nice..


The other infill that picked up which needs attention prior to use is a modern reproduction of a Norris A5. It has a Norris style depth & lateral adjuster. The cap iron looks new, though it too is missing the cap iron screw. It's possible I may only need the screw for this one, though screw size is critical for a Norris adjuster as that determins the slop in the adjustment. I haven't been keeping up with the infill kit plane makers to remember who to contact for this, and was hoping for suggestions. The adjuster screw hole appears to be 3/4" diameter. Not sure how much wiggle room is customary for this style adjustor. What size screw do you think I should be looking for? 11/16?


Thanks for your time,

Dave

Re: Infill cap iron questions *PICS*

#2

Re: Infill cap iron questions *PICS*

david weaver

It looks like the cap iron is not right for the first plane, and that button sticking up is usually below the screw, and with enough room so that it doesn't contact anything (obviously).

Perhaps that infill came with a tapered iron or one that was somehow thinner at the top, and a cap iron that's now long gone that gave some room. It does seem awfully tight below the lever cap.

With the second one, the cap iron screw should fit pretty flush in the adjuster so that there is effectively no slop. You could call Bob (i can't remember if that's his name) at st james bay tool company and see if he has something that would work.

Anyone can check their planes with adjusters to let you know if the cap iron screw is flush in all of them, but if nobody else does, I'll look to make sure I'm correct about the flushness of the fit. Ideally, the cap screw is fairly deep fitting and rounded at the edges to make it easy to get in the adjuster but still flush at the sides once it's in the whole way.

Re: Infill cap iron questions *PICS*

#3

Re: Infill cap iron questions *PICS*

Joel Moskowitz

The Spiers is a fairly late model version (I think from the lever cap screw - can't see the logo) and the lever cap is a replacement. It's an earlier style. later lever caps would be flush. If you grind down the brass insert it might come off (maybe not sure) get a new lever cap.

Re: Infill cap iron questions *PICS*

#4

Re: Infill cap iron questions *PICS* *LINK*

barryvabeach

Dave, the Norris style does not look like SJBTC adjuster I linked to an ebay ad for the SJBTC. It is hard to tell from the photo, but it looks more like the Ray Iles. Let me know if is is a Ray Iles, that Joel sells. I bought one of those adjuster from TFWW and can tell you the precise measurement of the screw if that is the one you have. IIRC, it is the same size as used on a Norris. Joel might even sell the screw.


img

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&_trksid=p4340.l2557&hash=item27c774e97c&item=170850052476&nma=true&pt=LH_DefaultDomain_0&rt=nc&si=dkW8ZUnF6LLjXTDqfI%252FrWGcNfuM%253D&orig_cvip=true&rt=nc#ht_500wt_1032