New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Branch section coasters - two questions

Posts

Branch section coasters - two questions

#1

Branch section coasters - two questions

Bill Houghton, Sebastopol, CA

A friend from our community choir has asked me to cut coasters from a couple of branch sections of a tree from her property. It's some kind of fairly dense conifer, about 3" in diameter. I've warned her already that they may check and warp.

I've never done anything like this before, so a couple of questions:

1. Is there some optimal thickness for something like this to minimize the chance of checking/warping?

2. I don't currently have enough sawdust to pack the cut sections in sawdust for drying, so I planned to put them in paper bags and warn her to watch for mold. Are there better techniques to promote gentle drying? Is the sawdust enough better than a bag that I should check around at local cabinet shops to see if I can get a bag of their sawdust (I doubt they charge for it...)?

Re: Branch section coasters - two questions

#2

Re: Branch section coasters - two questions

Tony - Memphis

I happen to have a section I cut from our Christmas tree to use as a coaster here in my office. It was probably a Noble fir. I cut them with a chop saw in 1/4"slices. I did absolutely nothing special to dry them. No cracking, checking, etc. I didn't finish them either. I have a large chunk of it with small holes driled in at various angles that I use as a pencil holder in my shop. No issues there either.

Tony

Re: Branch section coasters - two questions

#3

Re: Branch section coasters - two questions

James Watriss

There's an article from FWW # 169 that has Silas Kopf using such 'oysters' for veneer. He just cut them and stickered them to let them dry.

Because the circumference is so small, you should be fine.

Re: Branch section coasters - two questions

#4

Thanks, folks - helpful information


Re: Branch section coasters - two questions

#5

Re: Branch section coasters - two questions

Bob Hackett

I have been having excellent luck cutting discs from both branches and saplings in various hardwoods and putting them in a food dehydrator. In a couple of days they are bone dry and ready to sand and finish. I get about 20% loss due to cracking in tough to dry woods like Oak and Beech if the grain isn`t straight . I cut them on a diagonal to create an elliptical piece rather than round. Feedback has told me that folks like the way the bark can be seen from the top and the elliptical shape better than a round disc. The slices are cut at about 3/8 max and go directly from the bandsaw dripping wet into the dehydrator. I think the combination of the thickness and the fact that it`s all end grain exposed to warm always moving air has contributed to my success.

When I tried putting them bags or sawdust like I do with my much thicker bowl blanks all I got was moldy,stained wood that decayed rather than dried. The microwave just warped the heck out of them.

Let me know if I can be of any help to you Bill. Feel free to email me if you want.

Re: Branch section coasters - two questions

#6

Re: Branch section coasters - two questions

Pam Niedermayer

Bob, have you found a wood that soaks up moisture as well as cork?

Pam

Re: Branch section coasters - two questions

#7

Re: Branch section coasters - two questions

TomD

Cork is hygroscopic? I guess a cork from a bottle has some surface moisture to it, and it dries out if the bottles are stored upright. On the other hand it works great in wet environments like rod handles. How do you find it absorbant?

Amadou is a nice drying material

https://www.google.ca/search?q=amadou+for+drying&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-GB:official&client=firefox-a

Re: Branch section coasters - two questions

#8

Re: Branch section coasters - two questions

Pam Niedermayer

All I know is that every coaster I've ever bought (last set was some 30 years ago) was either made of cork or had a cork lining between glass and coaster. Or am I misremembering? It wasn't cork?

Thanks for the amadou reference, very interesting; but probably not what Bill had in mind.

Pam

Re: Branch section coasters - two questions

#9

Re: Branch section coasters - two questions

Bob Hackett

If you`re looking for something to absorb moisture then an open grain non resinous wood would be good. Aspen has been like a bundle of straws and wicks moisture like a sponge for me. I would think you`d want something that would resist moisture though if for no other reason than staining.

The slices I make are for a completely different application than coasters so I leave them unfinished and warn the folks who are going to use them that they`ll absorb pretty much whatever they put on them, drop them into,rub up against them or is likely to be transferred to them when they put them in contact with another object or surface .

Re: Branch section coasters - two questions

#10

Got it, thanks.


Re: Branch section coasters - two questions

#11

Re: Branch section coasters - two questions

TomD

Coasters are often cork, or at least some kind of aggregate of cork. But I would have thought that was because the cork was cushiony, heat resistant, and water proof. Who wants and old school finish with something wet sitting on it.

Re: Branch section coasters - two questions

#12

Re: Branch section coasters - two questions

Pam Niedermayer

Since my main concern was sweating glasses on wood, I of course assumed that was the reason for cork, which didn't rear its head in other land based situations. That could be wrong, very wrong, especially since it never did a great water soaking job for long. It's a moot point now, what with the scarcity of cork.

Pam

Re: Branch section coasters - two questions

#13

David Barnett

Think wine bottles stored horizontally, Pam...

David Barnett

... before screw caps and plastic plugs.

Re: Branch section coasters - two questions

#14

Re: Think wine bottles stored horizontally, Pam...

TomD

Yeah, they are in order to keep the corks wet, so the do get wet, but then most stuff in permanent exposure to water will take some on.

Cork scarcity is a bit like wood scarcity, they aren't making more of the stuff relative to expanding markets but you can get anything you want. Some good sellers on ebay. Of course cork is renewable, and unlike wood it's harvest seems responsible for the preservation of some fairly amazing forest lands that otherwise might be cut.

The cork one wants for fly rods is very hard, I don't think one could compress it into s wine bottle. It has the combination of being water proof to a sufficient degree, stiff so one can feel the slightest whispers in the rod, and light. There ought to be some superior material probably a foam, but not that I want to use. A hard foam might be abrasive to the hand. I shape and finish cork on the lathe with sand paper. I use very fine paper to wet sand it to a finish. It comes out looking a bit like marble when it is polished to the finest grits.

Re: Branch section coasters - two questions

#15

Re: Branch section coasters - two questions

eliot d

You may wish to check on the turning site, where this kind of question gets almost as much attention as, say, sharpening stones , here. I can tell you that if you make(turn) these coasters fairly thin, then the moisture can get out of them right away so that checking usually is minimized. If they are left somewhat thick, then certainly one way to hold checking back is to use sawdust in a bag and hope they don't check, They will warp, though. Then you can rework them later. Instead of sawdust, lot's of turners wrap pieces in paper bags and change the bags every so often. You'll see the moisture in the wet bags. Here the idea is have the moisture go out slowly because the wood is thicker and the stresses are greater if the moisture leaves too fast.