New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

cleaning a varnish brush

Posts

cleaning a varnish brush

#1

cleaning a varnish brush

John Pappas

This is based on a tip I got from Jeff Jewitt when he hosted a chat room on finishing many year ago. I just applied a coat of poly to a small desk top and thought I would pass this along.

Use a paper towel to remove as much of the poly as possible.

Dip the brush in mineral spirits. Key point here; it is not necessary to repeatedly wash in mineral spirits. Again, wipe brush with paper towels thoroughly to remove most of the mineral spirits.

Wash brush with Dawn dishwashing detergent repeatedly until it no longer feels oily.

Comb out the bristles and wrap brush in paper.

When that discussion came up in his finishing chat room, I questioned the 'dip brush in mineral spirits'. Yes, sounds inadequate, but it works. Try it on one of the cheap throw away brushes. You will be surprised, as I was.....and still am.

Re: cleaning a varnish brush

#2

Re: cleaning a varnish brush

TomD

Interesting, but if it doesn't involve a brush spinner, it can't be that much fun!

Re: cleaning a varnish brush

#3

LOL!


Re: cleaning a varnish brush

#4

Another one

Frank D. in Montreal

I tried to find Dawn and gave up (I've read a lot of Jewitt's stuff). Later I tried using vinegar after thinner and dish soap with water. Works like a charm. The vinegar leaves the brush really soft after it dries, and shortens the whole process of washing the brush. So a quick dip/rinse with solvent, a quick wash with dish soap and water, and a few good sprays with vinegar to get rid of all the residue.

Re: cleaning a varnish brush

#5

Re: cleaning a varnish brush

Bill Houghton, Sebastopol, CA

I use citrus based mechanic's soap, non gritty. I will have to try the vinegar.

Re: cleaning a varnish brush

#6

What is going on

Bill Tindall

The detergent will likely solubilze and disperse the remaining mineral spirits and the remains of the varnish dissolved in it just like it removes grease from your hands and clothes and dishes. But then so will the mineral spirits. I am failing to see the detergent advantage.

Myself, I use gasoline, three or four rinses and shakes. It is cheaper and a better solvent.

As far as the vinegar, I fail to see any reason that a five percent solution of acetic acid will have any effect on cleaning varnish from a brush. It may have some effect on the protein bristles if they are hair. I will have to test that possibility.

Re: cleaning a varnish brush

#7

Re: What is going on

John Pappas

Bill, how do dispose of the gasoline after using it? I used less than 1/2 inch of mineral spirits in a tuna fish can to dip my brush in. I then poured that into a container in which the sediment will eventually settle to the bottom. Then I'll transfer to another container for reuse. Cheap & effective.

Re: cleaning a varnish brush

#8

Made sense to me...

James Watriss

Solvent thins out the poly, but is still oily itself, and may still contain some of the poly, which will still harden on the brush when it dries. Wicking the thinned out poly with paper towel, and washing the remainder off with soap seems like a more thorough job to me.

I'm sure gasoline works well, too, but it would still leave an oily residue that could be removed with soap and water.

Not sure where the vinegar comes in, maybe the acid helps to emulsify the oil, and make it 'clumpier' and easier to remove. Just a guess. I'll have to give all this a try later.

Re: cleaning a varnish brush

#9

The principal of brush washing is straightforward

Bill Tindall

It is a classic problem of serial dilution.

Starting condition and assumptions(for example): shaken or spun or dabbed with towels the "dry" brush holds 25 grams of 40% solids.varnish, equal to 10 grams of varnish solids in the brush.

Round 1 Sozzle the brush in 75 grams solvent. The result is 10 grams of varnish solids in 100 grams total. Shake, spin or dab to leave 25 grams of solvent with2.5 grams of varnish solids remaining (75/100 of the varnish soldids left with the solvent shaken, dabbed or spun away)

Round 2 repeat step 1 with the result of .6 grams of varnish solids remaining.

Round 3 repeat step 2 with the result of 0.15 grams of varnish solids remaining.

If we quit washing at step 3, 0.15 grams of varnish will be left to harden in the brush. (likely unacceptable and one more step desirable)

One can clearly see that the biggest benefit that can be applied to brush washing is to remove as much solvent as possible after each washing step. More washing steps more quickly result in a cleaner brush. Least beneficial is increasing the amount of solvent used in each wash.

Soap is a crappy solvent for varnish. But, it will be effective at dispersing the solvent remaining in the brush in the case where this solvent contains but a small amount of varnish solids(all this has to do with the difficulty of dissolving polymers relative to the ease of dissolving and dispersing something like solvent). The resulting dispersion can be washed out with large amounts of cheap water to yield a brush essentially free of varnish solids. The benefit of the soap is ridding the brush of varnish solids, NOT solvent, which will readily evaporate in time.

The key to employing the soap "trick" is to dilute the varnish solids to the point where soap/detergent will disperse the solvent. If the varnish solids in the solvent are too concentrated the water will crash the varnish out of the solvent solution where it will stick to the bristles, forever.

How much the brush needs to be solvent washed before detergent treatment must be arrived at by experience. The answer apparently is less than I had assumed, but then the answer will depend on the details of the varnish formulation and the detergent formulation. All in all, an excellent idea to detergent wash the brush for maximum cleaning.

Re: cleaning a varnish brush

#10

Re: The principal of brush washing is straightforw

John Pappas

Thanks, Bill. As usual, your comments contain lots of wisdom.

Re: cleaning a varnish brush

#11

Re: The principal of brush washing is straightforw

Frank D. in Montreal

The issue for me was stiff bristles after using oil-based varnish or even some oil mixes, even after thorough washing with low-odour solvent then dish soap. Perhaps my washing technique leaves to be desired, but I don't like using toxic mineral-based solvents if I don't have to, much less spinning them all over my yard. Gasoline to me would be out of the question. What vinegar allowed me to do was eliminate the stiffness and keep solvent use down to a bare minimum (or eliminate it totally, when using oils like linseed). For me that makes sense, although chemically I have no idea what's going on.

PS for oil-based products I only use natural bristle brushes.

Re: cleaning a varnish brush

#12

guilty of premature dismissal

Bill Tindall

I didn't understand the description and the vinegar thing sounded like yet another bogus vinegar cleaning "Tip from Heloise". Your repost resulted in more attention and I don't like not understanding something that I think I should be able to understand. I don't what vinegar could do.

You said, "So a quick dip/rinse with solvent, a quick wash with dish soap and water, and a few good sprays with vinegar to get rid of all the residue."

Will you elaborate with enough detail that the experiment can be repeated?

After the quick solvent "dip/rinse" exactly what happens next with the brush now wet with solvent to remove solvent, if anything? Is it spun, dabbed with absorbant, shaken....?

More details on the soap wash. Is the brush now soggy with solvent sloshed in a bucket of soapy water, or what. How much soap, how much water, how many times this operation is repeated?

Spray with vinegar? Again more details. The vinegar is sprayed onto the bristles and not then removed or otherwise washed away?

Bottom line- help me to understand what steps remove the varnish solids from the bristles. The varnish solids must be removed. Dissolving them in something and removing what they are dissolved in is the only way to remove them.

Could the vinegar keep the resins from reacting with air and crosslinking? It would seem "not forever" because acetic acid is nearly as volatile as water and it would soon evaporate away. Acetic acid(vinegar) could be an excellent solvent for the metallic dryers, but these would have to be washed away with some rinse.

Re: cleaning a varnish brush

#13

no wisdom demonstrated

Bill Tindall

"Serial dilution" is the way most anything is washed out of something. We all understand the concept whether we know the name or not.