New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Building wooden flat bed truck bodies *LINK*

Posts

Building wooden flat bed truck bodies *LINK*

#1

James Pickering

Building wooden flat bed truck bodies *LINK*

James Pickering

In a posting on my "Late 1940s woodworking hand tool kit" thread Pam Niedermayer wrote:

"What did you use chisels for in the truck cabs and bodies? Were they wooden framed?"

I don't like asking fellow participants to go to an off-board web page, but I think that the link to the one at the bottom of this post provides a detailed answer to Pam's question -- the content is too extensive to copy and paste here:

The links at the bottom of the web page lead to some great photographs of such trucks.

James


Building wooden flat bed truck bodies

Re: Building wooden flat bed truck bodies *LINK*

#2

that was interesting....thanks

Bill Tindall

I suppose they were made from wood because all the steel was going into tanks and ships at that time?

Re: Building wooden flat bed truck bodies *LINK*

#3

James Pickering

Re: that was interesting....thanks

James Pickering

Thanks Bill - you wrote:

>>>

I suppose they were made from wood because all the steel was going into tanks and ships at that time?

<<<

That is a possibility although I never heard it expressed. I think it was because that was the way the industry was set-up, organized and stocked. Note that on my web page I point out that Tillotson's was transitioning to aluminum van bodies at that time.

James

Re: Building wooden flat bed truck bodies *LINK*

#4

I don't have nearly the depth of Mr. Pickering

Bill Houghton, Sebastopol, CA

in the field, but I did grow up in a car family.

Two sets of thoughts:

First, making components of a truck cab or flatbed for small-numbers production would be costly when made from steel; beating steel panels to a shape by hand is labor-intensive, and no doubt slower than shaping wood. Even if the shape is ultimately covered by steel panels, having the wood there as a buck, or a form to which to shape the panel, would be more efficient than shaping the panel "in space," without a clear shape right in front of you to work to. Coach-built cars were exorbitantly expensive at least partly because shaping panels costs time and therefore money.

The British held on to wood understructures for their vehicles much longer than the Americans (except, perhaps, for the wood-framed station wagons the Americans built into the fifties). They did it right up to the mid-50s; it's said that saws and chisels were an essential part of the toolkit for an MG TC/TD/TF owner, because the doors, parts of the chassis, etc. were built from wood, skinned in steel.

This may be partly because of limited production facilities, or small production runs compared to the American makers; it may be partly because British industry has a history of conservative approaches to change (when it didn't have an attitude of utter horror about the idea of change). But it was unlikely to have been just due to steel shortages.

Second, wood appeared as a component of automobiles for a longer time than folks realize. It faded in the 1950s in American cars, although, again, you might still find it in limited-production vehicles. But European cars used it in a lot of ways, because they found it cost-effective. The "hatch" on the back floor of our 1973 Volvo station wagon (under which would be found the third row seating, if you had ordered that; otherwise, it was storage space) was a piece of plywood, riveted to a piano hinge. I managed to break it, but, in Volvo's defense, I doubt they anticipated that someone would load a complete Studebaker truck motor and transmission into one of their wagons. (Had I broken it badly enough, I could have repaired it far more easily than a bent steel hatch.)

And the Triumph Spitfire our son briefly owned used plywood for both the dashboard and the "firewall" between seats and gas tank - this latter was one of the several reasons I was glad to see him sell it on to someone else.

I could babble on at some length, but it's late, and I would get even more boring than I've been; so I'll stop.

Re: Building wooden flat bed truck bodies *LINK*

#5

James Pickering

Thank you Bill for that great explanation

James Pickering

.......... I learned a lot from your post.

James