New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Shop-built toothing plane help

Posts

Shop-built toothing plane help

#1

Shop-built toothing plane help

Cecil Nickerson

I came across a laminated toothed iron from Sheffield and am finally getting around to building a smoother-sized plane for it. My initial thought was to bed the iron at 90 degrees (it's been sharpened at 40 degrees) but I'm second-guessing myself now and need some advice. Can anyone help me with this project? Thanks in advance for your thoughts.

Regards, Cecil

Re: Shop-built toothing plane help

#2

Re: Shop-built toothing plane help

Pam Niedermayer

I can try, but I've never made a toothing plane. I have a couple of old coffins that mount the blade almost vertically, not quite; but I also occasionally use a toothing blade with my LN LA Jack that's bedded much lower, at 12°. Both bedding angles work perfectly.

Pam

Re: Shop-built toothing plane help

#3

Re: Shop-built toothing plane help

TomD

Dean Torges turned a lot of people on to the toothing plane. His recipe consisted of bedding a ECE cutter at 75 degrees. His wedge was 12 degree, He opened the mouth at 87 degree, in the direction of the blade. He then drew a line at 55 degrees from say 1/4 ish above the mouth, this leaning back away from the iron. Then up that a bit he hogged out a big bay with a 2 inch radius. So the blade was bedded at 75, the mouth was a just less than vertical, and towards the blade, then leaned way forward, then a lot of wood was simply removed to provide room for the shavings.

Torges makes simple sawn planes like the Krenov ones, but used a dowel retaining pin.

This plane was designed to enhance glue joints and plane very difficult woods like Osage. Torges is a bowmaker, Osage one piece bows have to be pretty nice wood, but Osage bows that are backed, can use more normally occurring boards, and they are some of the worst for tear-out on will find.

Re: Shop-built toothing plane help

#4

It depends on which you want to do with it.

Derek Cohen (in Perth, Australia)

Do you want a scraper for veneer? If so, set the iron vertically.

Or do you want an alternative to a jack plane? If so, set the bed at 45 degrees.

Regards from Perth

Derek

Re: Shop-built toothing plane help

#5

Re: It depends on which you want to do with it.

TomD

By the by, Derek, do you know what angle the low angle bevel up LV plane is set-up for?

Re: Shop-built toothing plane help

#6

Big thank-you to all

Cecil Nickerson in Halfmoon Bay

I've now got a direction to head in. Thanks again.

Best wishes Cecil

Re: Shop-built toothing plane help

#7

Re: Big thank-you to all

TomD

Which is?

By the way Torges also cambered the iron.

Re: Shop-built toothing plane help

#8

Re: Big thank-you to all

Cecil Nickerson in Halfmoon Bay

I'll build one ay 90 degrees and see how that goes. I have three of the Sheffield irons and will build another at a lower angle to act as a jack plane.

Regards, Cecil

Re: Shop-built toothing plane help

#9

Re: Big thank-you to all

TomD

Then you will be the expert and can let up know what works. I am going to make one but need to take another swat at a blade with my shaper first.

Re: Shop-built toothing plane help

#10

Re: Big thank-you to all

Pam Niedermayer

Those jack teeth have come in very handy for knots and swirly/knarly grain. Have fun.

Pam

Re: Shop-built toothing plane help

#12

Re: Tom, 38 degree bevel on a 12 degree bed.

TomD

Thanks!

Re: Shop-built toothing plane help

#14

Re: Shop-built toothing plane help

Dale Stansbery

Here's a photo of my Ohio Tool bladed toothing plane. I think the body is original Ohio tool also that had the funky euro style handle retrofitted. It's an obvious retrofit that was inlet nicely, but not smoothed off very well at the back end. You can still see coping saw marks on the back bottom of the handle. There's no makers mark but I think it was removed by inletting the handle. The blade appears to be set at about 75-80 degrees and the serrations are pretty fine. It's probably only good for glue prep.The blade appears to have the original grind so I suspect it's seen very little use.