New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Question for LN plane users

Posts

Question for LN plane users

#1

Question for LN plane users

Joe in a Cleveland suburb

Hello.

Suppose Santa brought you a new LN plane. Pretend it was a 4-1/2 smoother.

After taking it out of the box and staring at it for a while, what do you do to prepare it for its first use?

Would you do anything to the sole? The chipbreaker? Hone the back of the blade? Hone a secondary bevel on the blade?

Thanks.

Re: Question for LN plane users

#2

Moses Yoder

Re: Question for LN plane users

Moses Yoder

It's very simple; sharpen the iron and use it. Naturally sharpening the iron includes polishing the back. I grind the bevel then hone only the front edge, and the way you go about honing depends on whether you use a guide or not. I use a guide, so all my honing is done at the same angle, no secondary bevel. I think if I were to go without a guide I would raise the angle a little bit for the final 8000 stone polishing. After sharpening the iron and using the plane you will find out if it needs further tuning; chances are it won't.

By the way, just for the record, you suck.

Re: Question for LN plane users

#3

Re: Question for LN plane users

Derek Cohen (in Perth, Australia)

Hone the bevel face and back (all blades need to be honed, no matter the company) ... and you should be set to go.

Enjoy!

Regards from Perth

Derek

Re: Question for LN plane users

#4

The very first thing I`d do...

Bob Hackett

Would be to try making shavings with it. If it performed as well as expected I`d continue to make shavings till I needed to stop for one reason or another.

If it din`t make shavings, after I got over my surprise, I`d polish the back and hone the bevel. :)

Re: Question for LN plane users

#5

Re: Question for LN plane users

David Weaver

As others have already said, polish the back of the iron, hone the bevel, check to make sure the chipbreaker is a good fit, wax the sole of the plane with paraffin and go.

I wouldn't touch the sole until it had enough wear to make that needed.

Re: Question for LN plane users

#6

I know

Joe in a Cleveland suburb

for the record, you suck

People tell me that all the time. But what does that have to do with this plane?...

:D

Thanks.

Re: Question for LN plane users

#7

Thanks guys.


Re: Question for LN plane users

#9

same here  (and congrats Joe, nice gift!)


Re: Question for LN plane users

#10

Re: Question for LN plane users

TomD

"Your Lie-Nielsen Bench Plane is ready to cut wood out of the box. The blade is ground sharp at a 25° bevel. A secondary bevel of up to 5 degrees helps achieve a razor edge quickly. This also improves edge life in hardwoods."

Might as well use it out of the box, if you do the blade, you will miss out on what they thought was good enough to send out. Planes like this used to take days of work to get working. I am glad those times are past.

Re: Question for LN plane users

#11

Bob...

Joe in a Cleveland suburb

This is the approach I will take. After reading your response to Bill T in the thread below, this makes sense.

I can play around with it a bit, then when I have the guts, I can polish the back and hone the bevel a little. This way, I'll know how it feels out of the box compared to how it feels after I screw it up trying to make it better... :)

Thanks.

Re: Question for LN plane users

#12

You`re most welcome.

Bob Hackett

I just pass on what I feel is useful info.

Re: Question for LN plane users

#13

Different take here

North of the Border

I'd just go ahead and use it -- yes, no honing of any kind as some suggested. Why? Unless we want to do some kind of analysis, as endusers, the blade is sharp enough, except for the very demanding grain or board. Now, after using it and feeling a honing is needed, then hone and polish it.

LN's planes (or for that matter, Veritas and even WR 3.0) are good enough when we get them, no need to split hair here. For many plane users, I can say, the benefit of honing the blade when received new will not be obvious to them anyway.