New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Nibbling to get a perfect fit *LINK*

Posts

Nibbling to get a perfect fit *LINK*

#1

Nibbling to get a perfect fit *LINK*

Bill Tindall

Since being shown this technique I have found many uses for the general concept of using some sort of jig block with an angle cut on it as a chisel guide to nibble a piece at the chosen angle.


Nibbling jig

Re: Nibbling to get a perfect fit *LINK*

#2

Re: Nibbling to get a perfect fit

Pam Niedermayer

Pretty common solution, albeit usually at 45 or 90 degrees. My real question is why you need to veneer the blades?

Pam

Re: Nibbling to get a perfect fit *LINK*

#3

Answer.....

Bill Tindall

Following the heading "Task at Hand" there follows "nibbling the length of the bull nose molding facing for the chest of drawers".

The blades are not being veneered, rather a bull nose molding is being applied to (1) cover up the dovetail joinery and (2) to bull nose the forward facing case edges as a design element. This detail will put a modern twist to an otherwise Federal-looking case.

This edge of the case side was bull nosed then a thin strip including the bull nose was ripped from the case side with a very narrow kerf blade before case assembly. Now it is being reapplied with additional strips to be applied to the blades.

I could add that it is a great relief that all the dart cut-outs for the blade molding stayed lined up and the bottom of the applied strip mated perfect with the base molding. Situations where there are no "degrees of freedom" in a fit are stressful for me and I proceed deliberately with the execution. Using a 45 degree jig block I will nibble away at the darts on the blade molding until I get good fits, but in this case I have extra pieces made if I screw up a fit. Gluing back the case edges that were originally ripped off in the beginning left no room for error. There aren't extra pieces....that would match grain and color.

Re: Nibbling to get a perfect fit *LINK*

#4

Re: Answer.....

Pam Niedermayer

Well, at least we agree on the veneering. :)

I confess that I've had more difficulty than usual translating words into images lately, probably from cutting down on coffee and weeds, so I looked at the photos, scanned the words.

Anyhow, so you want to hide the blade's dovetails with the sides. Why not make sliding dovetails that end well before the front? Or, barring that, why not put the molding on the sides?

Pam

Re: Nibbling to get a perfect fit *LINK*

#5

Re: Answer.....

Bill Tindall

If there is a way to bull nose the forward facing edges I was unable to think of it. Well actually I can think of a way that winds up looking crude. If the edges are bull nosed before case assembly the intersection of the blades with sides is abrupt, not at all pleasing like the flowing "dart" intersections. If all goes well the it will all be assembled and stained today and I will post a picture of this milestone.

Re: Nibbling to get a perfect fit *LINK*

#6

Re: Answer.....

Pam Niedermayer

I don't know anything about something called bull nosing, but there is a way to make the front a butt joint supported by a sliding dovetail, thus eliminating the need for molding. Or so it seems to me.

Or, maybe normal practice is to make the front a sliding dovetail and the back a butt joint?

Pam

Re: Nibbling to get a perfect fit *LINK*

#7

The problem to be solved...and the solution

Bill Tindall


If the front edge is bull nosed the intersection of the drawer blade edge with the case side edge becomes a problem. A butt joint will result in an abrupt intersection. A cope would be ok but the intersection would be a line off the line of the case edge which is not the most attractive option. Best will be a "double miter" or dart as I call them. In this case the profiles of each molding smoothly flow into one another.

Accomplishing this intersection with an applied face molding is not difficult. It is difficult to get the female part of the joints all aligned with the blades. But fitting the blade molding simply involves nibbling at the end miters until the piece is about 1/32" too long. A center line scribed on the back of this molding aids aligning the miter. Then it is simply sprung into place and this compression secures the end joints. Additionally the height of the bull nose profile will have to be refined so the intersections is the same height for each piece along the length of the joint (custom made profile will never be sufficiently precise to avoid some diddling with the intersecting height).