New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Stanley Plane screw sizes

Posts

Stanley Plane screw sizes

#1

Stanley Plane screw sizes

Clementine

I'm restoring a #5, but one screw refuses to come out. I may have to drill it out, but I seem to recall that Stanley used its own size of screws, not standard size screws. If so, I don't have a tap that would fit. Is this correct? If so, any suggestions?

Re: Stanley Plane screw sizes

#2

Re: Stanley Plane screw sizes

Bill Houghton, Sebastopol, CA

Stanley designed its planes during a period when standardization of screw sizes and pitches was nonexistent or in its infancy (depending on which plane). Some screws are of sizes/pitches that became standard sizes; some (maybe most) are not. About the only good news is that they were then fairly consistent, not changing screw sizes much. Which screw is misbehaving? If you can specify that, either someone here will know the size/pitch of the thread or one of us can measure it for you.

Suggestions: If you've got access to a propane or MAPP torch (or gas welding torch), heat up a piece of steel rod, say 3/8" diameter, and touch it to the head of the screw for 30 seconds or so, then remove. Don't do this if the screw in question is holding the tote or knob or any other wooden part. This will often break loose the corrosion in the threads.

If you've been using WD-40 as your penetrating oil, see if you can find Kano Kroil or mix up a 50/50 brew of automatic transmission fluid and acetone. Either of these has proven to be a better penetrating oil than WD-40.

If you can support the plane casting in a way that you are absolutely SURE you won't break it with this approach, set the correctly sized, plastic handled screwdriver in the screw slot and strike it a firm blow with a moderately heavy hammer. Again, the shock will often break loose the corrosion. This particular trick always scares the heck out of me when applied to the fairly thin casting sections on a plane, so I use it only when I've given up on other approaches.

Re: Stanley Plane screw sizes

#3

Jack Guzman from Maine

One other trick

Jack Guzman from Maine

Electrolosis will sometimes loosen up rusted threads. Read about it in the articles section.---Jack

Re: Stanley Plane screw sizes

#4

whacking threaded fasteners

Bill Tindall

I had a recalcitrant set screw and a maintenance man told me to flood it with good penetrating fluid, set the driver and whack it smartly. The suggestion struck me as preposterous, so it became the last thing I tried. It worked as if by magic.

I suppose the shock makes a micro crack that enables the penetrating fluid to penetrate the corroded interface. In any case it is now the first thing I try.

Re: Stanley Plane screw sizes

#5

Re: Stanley Plane screw sizes

JMOHNIKE

I have done this one time and it worked. I placed the plane body, everything elses removed, in an oven set at 450 and let it get hot. When it was hot I poured break fluid on to the screw, a lite tap and the screw came out. I was given this trick by my father inlaw who used it on old farm equipment, cars trucks etc. I have used it on other things useing a torch and it has always worked when everything else failed. I used an oven for even heating to avoid warping of the plane.

Re: Stanley Plane screw sizes

#6

scott grandstaff

Re: whacking threaded fasteners

scott grandstaff

A decent quality hand impact driver work wonders sometimes.

MuCh better than just whacking a screwdriver.

Just be sure to test the driver. Never trust the switch setting!

Simply press it against a sacrificial surface (scrap of wood) with your hands and if it spins in reverse as you push, you are good to go.

Otherwise change the switch and test again.

Also test once in a while as you work.

A good working impact driver (with a tip that fits the screw!!!)

and penetrating oil, and patience,

you can get most anything loose.

Yours Scott

Re: Stanley Plane screw sizes

#7

Re: Stanley Plane screw sizes

Clementine

Hadn't thought of the oven treatment. I may try it later. Tried some of the other ideas, but no luck. I put the plane back into electrolysis and walked away.