New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Random terms

Posts

Random terms

#1

Random terms

TomD

My mother is making some comments on the 150th anniversary of their church building. She had earlier published a history of the church. On one page of history there is a very bad and small picture of two tools owned by the builder. Neither looks very church buildy to me. One is a slitting cutter, the other is a large block like plane with a skewed cutter. The maker was a local builder of everything from skiffs to churches. The plane looks like something that might have been used to raise panels, and the slitting cutter is not fancy but looks like a bench tool nonetheless.

In the west, what is a "slitting cutter" used for? The one I have is Japanese and is used for breaking out Shoji dividers, and as a large marking gauge. I could see this western version being used also for marking, and splitting, maybe lath, maybe drawer bottoms, very fine drawer sides?

My mother also wants to refer to the timber frame as being pegged with trunnels. My use of the that term would apply to flat nailing stuff like the seats of Adi. chairs or planking to frame on carvel boats. The things that go in timber frame mortises I just call "pegs". Anyone know.

Any idea about a large handleless skewed block plane, square in section, not the molding plane shape with the flag like blade. Full width blade, skewed, no handle, can't tell whether the blade cuts to the edge of the block or not.

Re: Random terms

#2

Re: Random terms

Pam Niedermayer

"Trunnel" is slang/a contraction of "tree nail," thus pegs.

Pam

Re: Random terms

#3

scott grandstaff

Re: Random terms

scott grandstaff

So, 1860 more or less?

You are both right

Trunnel is just short for tree nail. So peg, dowel and trunnel all mean the same thing.

You are looking at a badger plane. The skewed blade is the tipoff. It probably does cut all the way to one side for panel raising, but even if it doesn't its still a badger. Toteless is unusual. He wasn't an Englishman, whoever your builder was. Unless the tote was just missing in action?

1860 would have had Disston style saws on the jobsite. Barton, L&J White, Underhill or Whitherby chisels to name a few.

Beams would have likely been broad ax squared and adze cleaned. People were still fast/skilled at it and it was inexpensive.

Unless it was a large city, then sawmilled.

Planks were sawed and by the 60's sawmills were in wide use. Steam or water powered, but sawmills just the same.

Large hatchets would have been employed, many carrying one.

Beam drills would be in use by then, as well as T augers.

In 1860 the industrial revolution was in full swing. Machine shaped moldings, window frames and trim would be available unless you were way deep in the country and even then probably shipped in for church work.

yours Scott

Re: Random terms

#4

Re: Random terms

Warren in Lancaster, PA

I think in the 19th century "trunnels" was used for ship building and maybe bridges, not for buildings. Nicholson used "pins" for timber framing. However I don't think use of either pegs, pins, or trunnels is confusing in this context.

I think your plane is a skew rabbet, probably 1 1/2 to 2 inches wide, which would be useful for carpentry. After the mid 19th century they were often called badger planes.

Re: Random terms

#5

Re: Random terms

TomD

Thanks, great stuff.

I have seen pins also. The derivation doesn't really help, since the usage will vary. I never remember anyone saying pass the "treenail" at a timber framer's guild raising. But then they were all made by the one company, so it could even have been a kleenex type thing where they are called by what is on the box.

Speaking of pegs.us:

"Specializing in pegs and trunnels for timber frame and

covered bridge construction, and boat building."

The only place trunnel is used on the price list is in relation to boat building. For what that is worth.

"Badger Plane". Cool.

Re: Random terms

#6

Re: Random terms

TomD

Thanks Scott, great elaboration. The plane acutually looks a little Japanese! Behind the blade it has about the same length and roundover as a Japanese smoother. The tote section appears to have been removed. The area is Douglas Harbour in New Brunswick. So anything goes. Saint John, downriver, was a fair shipbuilding town.

Any guess on what kind of slitting the gauge did around a church building site, or would it have even been there?

Re: Random terms

#7

scott grandstaff

Re: Random terms

scott grandstaff

Are you sure the slitting gauge isn't just a normal panel gauge with a sharp blade, left extended?

First thing I do on any gauge I get with a pin, is reshape that pin into a tiny knife. Pins are so raggedy in use, I hate em. :)

Plus a sharp knife shaped the right way, pulls the gauge tighter to the work as you go.

I am left handed so I shape my pins for southpaw.

When I am dead, and my tools are redistributed,

some rightie is going to scratch his head over me!

It'll be the old..... "What idiot made this thing? It doesn't work at all." heh heh heh

In fact, unless you are a "demonic possessed lefty" just be -very- careful at my estate sale. heehehe

yours Scott

Re: Random terms

#8

Re: Random terms

TomD

Looks a lot like this one:

http://www.woodmagazine.com/woodworking-tools/hand/the-slitting-cutter/

I will try and get a copy of the pic, but the source is pretty bad.

Re: Random terms

#9

Re: Photo

TomD

I found my old SONY that shoots to 3.5 inch discs, but it is good at hand holding this kind of thing:

[

Re: Random terms

#10

Re: Random terms

Frank H

I mostly come across "trennels" as a contraction of "tree nails" in Europe.

They are usually riven from offcuts of the timber being joined so there is no grain runout. They are roughly square, and are bashed into a round hole too small for them, so that the wood is deformed. A slight taper with a chisel at one end helps.

Great fun and easy to use for wooden structures in the garden with freshly felled timber, but have a history in building work with drier timber, and even harpischord construction (presumably with well seasoned wood ).

At a time when nails were expensive and screws very expensive, they were a good workshop-made alternative. I doubt anybody would have considered buying them.

I guess that a "peg" is round and, unlike a trennel, is not intended to cause deformation of the material; but most construction workers were (and are) more interested in getting the job done than worrying about proper names or spelling.

Frank.

Re: Random terms

#11

tool use depends on the wood

Ian (in Sydney, Australia)

Hi Tom

The badger plane could have been used to form rebates for window sills and other areas where the rebate needs to slope one way so that water runs off

does the church still have it's original pews? If so, is the seat or back a single board?

the panel gauge could have been used to mark the final width of wide boards, the boards then being brought to the desired width with either a hatchet, a side axe, or an adze. My father used to talk about a church he saw over 60 years ago where the pews were constructed with an adze

Re: Random terms

#12

Re: Random terms

Pam Niedermayer

I first heard the term in a Kingshott video, in which he said he had been required to cut them all the time as an apprentice. Now I don't know what type he made for what type of item; but in the video he worked one into roundish with a chisel like people do spindles with spokeshaves or drawknives who aren't using lathes, and he showed one that had been used in a famous big boat that looked very round.

I recently got some small Japanese wooden "nails" from Stu Tierney that I have yet to use, but hold great promise for.

Pam

Re: Random terms

#13

Re: Random terms

Frank H

Not a big surprise. I think I first saw the technique in an article by Kingshott in a magazine, where he described their use in wet timber.

The first time I tried it, I made them square(ish) with rounded corners, and too small - they fell out. It is surprising how much deformation wet timber will take (and needs) if you come from a dry wood background.

I have no doubt that for seasoned wood, a much rounder style and less force to fit would be necessary to avoid splitting. Of course, someone who uses the method regularly would learn the balance between poor enough fit to hold and good enough to avoid damage.

A bit like harpsichord strings (you may guess I have an interest):

"Question - when is a harpsichord string at optimum tension?

Answer - just before it breaks."

Frank.