New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

False fronts

Posts

False fronts

#1

False fronts

Patrick Gibbons

With all this talk on drawer making, I was wondering what the general consensus was about false fronts. I'm getting ready to make two drawers and false fronts seem to be a good way to go for these. Should the fronts be glued to the drawer or not?

Re: False fronts

#2

I don't like them

Bill Tindall

They make for a clunky looking drawer with the front added to the thickness of the drawer box. If they were a good idea for furniture they would have been used in 1750 (or 1850, etc.).

Re: False fronts

#3

Screwed, not glued

Andrew F in Australia

Hi Patrick,

They're typically screwed on, not glued on.

No problems with them, myself. Make life a lot easier.

CHeers,

Andrew F

Re: False fronts

#4

Re: I don't like them

TomD

I didn't realize they had full extension slides back then? :)

Not fine woodworking. But the funny part is that most people really don't want fine casework. I live in a world of heavy objects so I think they have a place, just not on a reproduction highboy.

Screwed not glued, assuming they have the usual beef. There could be some clever locator work going on though like alignment dowels.

An alternative is sliding dovetails. My dad used to run this university and he knew the guy who made the furniture for the student rooms. That was how he did stuff like heavy filing drawers. The sides were sliding dovetailed into the front. Single thickness front, all the inset for the side you want. 18 year old proof.

Re: False fronts

#5

Re: False fronts

Frank D. in Montreal

I use glue to locate the fronts: tape a shim to the back of the drawer so it sits about an eighth proud of it's closed position, then add a few dabs of quick-set glue (hot glue works well) and position the front on to the drawer. When the glue sets you take the drawer out and screw on the front on. Perfect fit every time.

Re: False fronts

#6

Re: False fronts

TomD

Often the handle holes will provide a means of aligning the fronts until you can get them screwed from the back. This ensures a zero gap from glue, and no time to do the glue or worry about it setting up.

Re: False fronts

#7

Only useful to me with guides...

John in NM

But they are certainly useful then.

I size them to the opening, then hold them on with double sided tape, locate screw holes, remove tape and screw them on. No glue needed.

Re: False fronts

#8

Moses Yoder

Re: False fronts

Moses Yoder

If you have an air nailer, you can nail the front to the drawer with an 18 gauge nail at each end, then adjust it into final position with a rubber mallet before screwing it on. I don't entirely agree that everything good was invented by 1750, so I use sub fronts on almost all my drawers because it is so much easier to cut a through dovetail. If I was a full time professional cutting half blind dovetails every day it would be different.

Re: False fronts

#9

is there general consensus?

Ian (in Sydney, Australia)

I like 'em when for you're dealing with drawer fronts that are angled or curved.

Make a standard rectangular drawer box and then attach the false front to match the slant or curve of the carcass

Re: False fronts

#10

How to solve this problem

Bill Tindall

To screw the false front on the front needs to be fairly thick, I would think at least 1/2". And the drawer box needs to be on the order of 1/2". For an inset drawer this yields a drawer front of 1" total thickness which, which is visually a fat drawer in a fine piece of furniture. If the drawer is to be lipped the situation worsens. A 1/2" lipped drawer just sticks out too far , again in a fine piece of furniture.

It is common in kitchens to have false fronts and applied doors sticking out 3/4" from the frames, which I find visually unattractive.

I have no quibbles with false fronts in more utilitarian situations. But unless there is a way to utilize something on the order of a 1/4 to 3/8 inch thick for a false front I don't see the false front as an attractive application in fine furniture.

Re: False fronts

#11

Re: is there general consensus?

Patrick Gibbons

My drawer fronts need to be outside the frame for my design to work. I don't see any other alternative but false fronts, unless of course I change my design, which I've been doing a lot as I go along.

Re: False fronts

#12

This is digressing from your question

Bill Houghton, Sebastopol, CA

I've seen a couple of nice modern designs (British makers, as I recall) that use color contrast between the front of the drawer box and the false front effectively by routing drawer pulls all the way through the false front, letting the drawer box show inside the drawer pull hole.

I'm with Bill T. on this, that for fine furniture, false fronts are generally an awkward solution; but the drawer pull design demonstrates that you can turn the awkwardness into design.

Re: False fronts

#13

I've had to change my design again

Patrick Gibbons

and it looks like false fronts are out. But don't hold your breath, I'm still ruminating.

Re: False fronts

#14

Post the big picture......

Bill Tindall

......and maybe one of the creative participants will have a creative solution to your drawer problem.

Re: False fronts

#15

An example of a false front

Ian (in Sydney, Australia)

the front of this chest of drawers is carved like ripples on a stream. It's quite tactile and stunning in the flesh.

I can't see how to make the item without using false fronts.

Re: False fronts

#16

A good application it would seem

Bill Tindall

In this case the false fronts don't stick out beyond the cabinetry frame, so they don't have the "stuck on" applied look about them as is the case of a 3/4" applied lipped face stuck on a drawer box.

It still look clunky when the drawer is opened, but that is the price for a sculptured front.

Re: False fronts

#17

Re: False fronts

Bruce, a MN Galoot

I've made drawers with false fronts either way, depending on grain orientation. For drawers that had the applied front with vertical grain, they're screwed. Grain that runs horizontally can be either screwed or glued.