New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Machine aided dovetail waste removal

Posts

Machine aided dovetail waste removal

#1

Machine aided dovetail waste removal

Bill Tindall

Andrew alluded to a router(trimmer) technique that I didn't understand. It sounded unduly complicated by involving setting up a fence. (It is entirely Andrew's fault that machines have crept into the Hand Tool Forum.)

I fix the drawer front back side up on the bench. Set a 1/4 or 3/8" straight router bit exactly the depth that the tails are long. In a series of clockwise arcs starting at the right side of the waste, route away the waste to near the saw lines, and base line. With good lighting I route free-hand to within 1/64" of the base line and about 1/32 to the saw line. I bought a new light weight router with LED lighting just for this task, and hinge mortises. A sharp bit makes this operation go smoothly. I understand the Lonnie Bird shop teaches this technique.

In the Headley shop they remove the waste with a hollow chisel mortiser. A fence is set up to locate the mortise exactly at the baseline and the depth is just shy of the tail length. This approach has the advantage of leaving long grain to pare to get the tail depth perfect. The disadvantage is setting up the mortise machine fence. However, they always use the same drawer thickness so the fence set-up can be made quick. I don't have a fence arrangement that is quick to precisely locate or I would use this approach as it avoids end grain paring to the baseline for the drawer thickness.

Personally I am not wedded to hand tool dovetail waste removal. I regard it a tedious task to be minimized. I route out the half blinds and band saw away the through dovetail waste. A band saw can be used as a micro-chisel and waste removed right to, or very nearly to, a scribed base line (again a Headley shop technique).

Re: Machine aided dovetail waste removal

#2

Re: Machine aided dovetail waste removal

Derek Cohen (in Perth, Australia)

Hi Bill

I have done two complete pin sides using a small router (actually before Andrew's post - a reassuring coincidence). I shall post pictures tomorrow.

Regards from Perth

Derek

Re: Machine aided dovetail waste removal

#3

Re: Machine aided dovetail waste removal

roninkokomo

I have seen guys do it with a scroll saw. They stay just off the line and pare.

Re: Machine aided dovetail waste removal

#4

Re: Machine aided dovetail waste removal

Sgian Dubh

Bill, here's a couple of snaps from some time in the mid or late '90s of a typical router set-up of mine for doing something very similar what you describe. It's an old and useful trick that can sometimes... well, quite often, save time. In this case it's on the waste of through dovetails for both the pin board and the tail board of a drawer or drawers.

Setting up the router to hack out waste between pins on a drawer front with lap dovetails is essentially the same thing. I guess the difference is that I've always been much more adventurous than you in that I set the router to the full depth required and set the side fence to precisely define the shoulder line-- it saves quite a bit of fiddling with a chisel sneaking up to those points. Slainte.

Photobucket

Photobucket

Re: Machine aided dovetail waste removal

#5

Re: Machine aided dovetail waste removal

TomD

The smart way to do it is with a fly cutter. This essentially saws the waste out on boards up to 3/4" thick. And you could do a pass from either side if you wished to. I use this on blanket box type situations where there can be a fair amount of space between pins. Every joint requires you to chop the equivalent of one board end off with a chisel. Where that amount is disproportionately on one board, the fly cutter does a great job. I always figured I would do an article on this method because as far as I know I invented it, but it isn't all that sexy being part machine, and part hand. On the other hand it is that effective. My favourite aspect of this method is less noise, vibration, and dust than other dovetail methods.

Re: Machine aided dovetail waste removal

#7

Re: What is a fly cutter?

TomD

Slotting cutter. I use one with a 1/16" blade, I think I got it at LV, but checking the smallest they currently sell is a 1/8". But it is a standard item. I also use a custom shank, but the regular ones will do all your drawers etc... right out of the box. I just square up a 2x4 that gets clamped to the back of the work so that I have a positive registration.

Here is one:

http://www.toolstoday.com/p-5168-slotting-cutter-assemblies-3-wing-14-inch-shank.aspx

http://www.amazon.com/Freud-63-150-16-Inch-Cutter-16-Inchdepth/dp/B0002TUCZW/ref=sr_1_1?ie=UTF8&qid=1317580474&sr=8-1

I have a few tricks to make this work nicely, but hey, wait for the article... ;)