New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Preparing drawer sides in pairs

Posts

Preparing drawer sides in pairs

#1

Preparing drawer sides in pairs

Bill Tindall


In our ongoing discussion of drawer preparation there is yet another variable, whether to do the sides as pairs. It is a technique I picked up from a professional shop. I find it it nearly halves the time to make the sides with no disadvantage I have found.

The rough cut sides are nailed together with two nails on diagonal corners which keep the pieces from moving during subsequent operations. I find the brads from a brad nailer hold better than round brads. Then the pair of boards are trimmed to size, dovetails marked, sawed and the bulk of the waste removed by your favored technique (I prefer a band saw to the tedious coping saw). Lastly the boards are separated, the baseline marked on the internal faces and the waste pared to the baseline.

On this drawer I choose to use a perky 12 degree tail rather than my customary 10 degree tail. The 12 degree tail makes waste removal in the half blind more difficult and I will likely not use it again.

Note the perfectly sized pin holes, a result of the marking device described earlier. It seemed to get lost in the discussion but the major advantage of this marking devise is that it ensures identical sized pin holes between the tails. Differences in the size of the large tails is not noticeable, but even small variations in the small pin size will be apparent.

A previous critic asked what was to be done with the offensive nail hole. That comment gets to drawer philosophy. It's just a drawer for heavens sake, held together with functional dovetails. Not the place I choose to make a design statement nor a place where I choose to flaunt my skills, not that I have much to flaunt. I just leave the nail hole. When planing the side to fit it largely disapperas, but it could easily be filled.

Re: Preparing drawer sides in pairs

#2

Re: Preparing drawer sides in pairs

GolfSteve in Calgary

I do this for most of my drawers, but do not use a nail. I just hold the pieces together and ensure they are aligned while I tighten them into the vise.

It saves a bit of time for the tail board (tails first), but the most time consuming task for me is cutting the matching profile on the pin board, and this technique saves no time there.

Steven

Re: Preparing drawer sides in pairs

#3

gang chopping the sides

Bill Tindall


The sides are still nailed together at this point, ie. there are 6 drawer sides on the bench. I chop what I can and then separate the sides, remove the nails and finish chopping.

The unconventional "dovetailing" mallet has a story. It is the oldest tool I bought. When the textile mills closed in Utica, NY in the 50's one was converted to a "Harbor Freight" kind of import place except stuff back then came from Japan and the place sold more than tools. The mill smelled like old oil from the line shafts. I would go there with my mother to shop. I had a modest allowance to spend. For a reason long forgotten I bought this mallet and amazingly I never lost it over the ages. I never really used it till "modern times". For me, grasped near its basher end, it is the ideal weight for tapping the chisel to remove dovetail waste.

Re: Preparing drawer sides in pairs

#4

Tools from our youth

Bill Houghton, Sebastopol, CA

I own a heavy ball peen hammer (24-32 oz., somewhere in that range), my first hammer at age 19, on which I installed a short handle, probably from a mason's hammer, because a proper length handle wouldn't fit in the converted fishing tackle box I was then using. It still comes in might handy in work in tight spaces, even though I now have an embarrassing number of hammers.

Re: Preparing drawer sides in pairs

#5

There was probably a reason......

Bill Tindall

I was allowed to buy a rubber hammer. I recall my grandfather telling someone that I could break an anvil. You must have been more trustworthy.

Re: Preparing drawer sides in pairs

#6

No, I was out in the world and on my own

Bill Houghton, Sebastopol, CA

No one to tell me I couldn't have a hammer that big. Broke my share of things with it, too.