New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Somedays I should stay in bed.

Posts

Somedays I should stay in bed.

#1

Somedays I should stay in bed.

Derek Cohen (in Perth, Australia)

Last weekend I was looking forward to a little more time in the shop working on the two military chests I am building (for use an an entertainment centre). Well, I spent more time repairing mistakes than moving forward.

Where I had left off last time was this - two carcasses in Jarrah dovetailed together with centre divider. These are 900mm x 525mm each, and will make up a long, low cabinet 1810 in length.


I was looking forward to turning this pile of boards into supports for the drawers ...


The initial part of the WIP is on my website: http://www.inthewoodshop.com/Furniture/DesigningandBuildinganEntertainmentCentre.html

First I decided to plough the rebates for the back of the cabinets before turning to the mortice-and-tenoning. That is when I really should have gone back to bed.

I usually double- and sometimes treble-check everything. Not because I am a careful, but because I am prone to getting things back-to-front. Call me spatially-challenged.

Well, in spite of this I managed to play a rebate on the outside of the cabinet! B-----r. How did I do this? I suppose that the inside and the outside look the same ..

It was easily repaired by glueing in a matching piece. It will not be seen ...


Then blow me down, I did it again - this time getting the back and the front mixed up! B-----r again!


OK, so you think it doesn't get worse. But I was on a streak - it comes in threes, not so? Oh yes, I did it a third time!

Here you can see the repair being planed down, and the other side has the correct rebate ...


That was Saturday. Sunday was better. I completed all the supports for the drawers for one of the units - I decided to do them one at a time since they were not exactly the same (one side has two colums of three drawers, and the other has a column of drawers alongside a column of shelves).

Today I made the stopped dados, and glued together the shelves.

At the end of the day this is where the project stood (everything is just a dry fit) ...


The one carcass is done and ready to install the 6 drawers (I am looking forward to that time - I love building drawers).


The other carcass needs drawer supports and shelves, and both sides need stopped dados.


The inside of the area for the shelves has been scraped, and the repair looks decent. With finishing it will be difficult to detect.


Onto the next time.

Regards from Perth

Derek

Re: Somedays I should stay in bed.

#2

You might not be the only one..

Bruce, a MN Galoot

BTDT, got the t-shirt. You're just man enough to admit it :D

Nice recovery.

Re: Somedays I should stay in bed.

#3

Chalk is your helper

Bill Tindall

I have a piece of chalk, can't remember the source, that is about 1 1/4 " diameter and soft, unlike the hard 1/2" diameter common chalk. I mark panels with it and much else. I'll have arrows and notes all over a carcass side to preclude repeating your problem, which I am also prone to.

The soft chalk doesn't scratch the wood and it makes a bold line.

If anyone knows where to buy this "5/4"chalk I would like to know as I need to replace my piece.

Re: Somedays I should stay in bed.

#4

Re: Chalk is your helper

Victor P

Home made chalk just found this while googling sidewalk chalk...

1. Find a mold for your sidewalk chalk. Anything from a toilet tissue roll or small paper cup to fancy candy molds will work.

2. Mix together 1 cup of Plaster of Paris with 3/4 cup of water.

3. Add color to your mixture using powdered tempera paint.

4. Blend well and let stand for a few minutes.

5. Pour your mixture into the molds you chose.

6. Set aside and let dry completely.

7. Once dry you can remove your chalk from the mold.

8. Set it aside to dry for approximately 24 hours more.

9. Take your chalk outside and create fun masterpieces!

Victor in Houston

Re: Somedays I should stay in bed.

#5

Neat, and worth keeping

Bill Houghton, Sebastopol, CA

although I think Plaster of Paris might be a tad harder than Bill Tindall was seeking.

Still, for anyone with kids or grandkids, this recipe could be right handy.

Re: Somedays I should stay in bed.

#6

Re: Chalk is your helper

Bill Tindall


This pictures shows a cherry panel for the side of a chest of drawers I am making. TR is top of panel right side.


This picture shows the chalk I am looking for. You can see how little I have left.

Re: Somedays I should stay in bed.

#7

Re: Chalk is your helper

Ron in Sterling, CT

Bill,

I use the chalk that the kids write on the sidewalk with. It does the job for me. My panels have more writing on them than yours by the time I get done. You can get it at the dollar stores, or Walmart.

Ron

Re: Somedays I should stay in bed.

#8

question

Bill Tindall

I have always been fearful of using the colored stuff. Does it become invisible upon finishing the panel without undue effort to remove it?

Re: Somedays I should stay in bed.

#9

Re: Chalk is your helper

Derek Cohen (in Perth, Australia)

I use coloured pencils. The trouble is that they are not durable and the marks fade quickly. I have been wary of using chalk with Jarrah as the grain is quite open and I fear that chalk residue will lodge there and affect the finish. I think that it is time to test some out as it certainly is more visible. Plus use pieces of coloured tape.

Here is a picture of the dovetailed cabinets placed edge-to-edge. You can just barely see the writing. This is the problem ..


Regards from Perth

Derek

Re: Somedays I should stay in bed.

#10

So is ink, comes in black, orange, & white.

Pam Niedermayer - Austin, TX

Re: Somedays I should stay in bed.

#11

"colorless" chalk

Bill Tindall

Chalk particles are actually colorless. They look white because light is scattered due to the huge refractive index difference between air and chalk particles. This differences in refractive index becomes insignificant when the finish is added and any chalk left-overs disappear. I use chalk on oak, walnut...any wood. (However, confirm this observation in your case.)

I would not use anything soft and colored like crayon, for the reasons you state. It could get in the pores and be there forever.

I live in fear of mis-cuts so I mark everything I can think of to diminish my propensity to loose concentration. Any wood to be removed (eg. dovetail waste, rabbits, dadoes, etc.) has indelible marks (black gel ink shows up on anything including walnut, it's reflective), panel orientations get marked, etc.

I have a problem working in short spells. My mistakes come when I leave something midstream and return thinking I remember where I was at.

Re: Somedays I should stay in bed.

#12

Re: Chalk is your helper

David Weaver

Maybe ding them on the inside with a short chisel with marks to denote front and back and matching joints.

I have the same problem. I do it at work, too, though that's numerical and not woodworking - spend hours preparing some complex scenario and then switch around two variables right at the end.

I think no matter how intelligent you are, this is one thing where thinking more about it doesn't make it less likely to happen - it may even cause "brain scramble" and make it more likely if you fatigue your head with repetition and try to think about everything at once.

But you'd be an expert on such a thing much more than I am - I've just noticed the same types of errors I make at work... I make in the shop, too. Process can minimize (to take some weight off of my brain thinking the same things over and over when I only need to think about them at execution time), but I haven't yet figured out how to eliminate.

Bad day in the shop should still be better than a day out of it, though.

Re: Somedays I should stay in bed.

#13

Re: Chalk is your helper *LINK*

Stuart Johnson

You might check these folks. It looks like they make something for everybody.


Wallbuck chalk

Re: Somedays I should stay in bed.

#14

that's it

Bill Tindall

Unfortunately it is packed 124 to the box. But it is cheap.

Re: Somedays I should stay in bed.

#15

Re: that's it

George Symula

Bill,

Google under, "Jumbo Chalk" turns up several choices including Amazon. A couple of bucks for six 1" X 4" sticks.

Re: Somedays I should stay in bed.

#16

Re: Chalk is your helper

Pam Niedermayer - Austin, TX

There is a certain type of intelligence that does help avoid such events, one in which a great number of things are kept in the mind concurrently. This was vital in developing software, during which it was required that the developer keep 200-300 things in mind at once. One stops being a developer when one can no longer do that, when the frontal cortex starts degenerating. I suspect it's roughly the same for an applied mathematician.

Pam

Re: Somedays I should stay in bed.

#17

Re: Chalk is your helper

David Weaver

I think my mind degenerated when I was about 10.

I run along a balance beam as an applied mathematician, determining what i can keep in my head at one time and what I can't.

Unfortunately, it is just as you're describing, there are dozens or hundreds of things that have to be resident to avoid looking at something later and saying "how did that get by me?".

I like woodworking to not be that way, and have a little more success with woodworking relying on method.

At work, relying on method only, unquestioningly, can lead to horrible mistakes. Relying on iterative examination to the extreme can lead to unproductivity. It's difficult to figure out how much of each I can apply and still work at an acceptable rate while doing what I hate more than anything in the world- making mistakes.

Re: Somedays I should stay in bed.

#18

Re: question

Ron in Sterling, CT

Bill,

I use the light yellow, and don't press hard. Most of it cleans off easy with a bench brush, and by the time I get done sanding there isn't any trace of it left.

By the way, I give the other colors to the neighbor kids to write on the sidewalks and driveways with.

Ron

Re: Somedays I should stay in bed.

#19

Re: Chalk is your helper

Pam Niedermayer - Austin, TX

I think woodworking requires considering about 20 things at once, any less and I'd find it too boring. I also think part of developing a ww skill set is learning how to think of those things, so I don't make piles of silly little mistakes. And in fact, as one gets better at these skills, one doesn't have to worry about making mistakes all the time, so one can get down to the task at hand, making good stuff. Same with higher density skill sets, the more one can leave conscious thought about mistakes behind, the better one is at the task.

Pam

Re: Somedays I should stay in bed.

#20

chalk chuck

McKay

I use a quilters chalk chuck. The chalk will come in many colors that show up better with the QSWO that I use. The chalk is about 5mm in diameter, but that is a plus to me. The chalk chuck also fits in my apron pocket for an easy grab.

Re: Somedays I should stay in bed.

#21

Plaster?

Tony - Memphis

Is that why plaster can be used as grain filler? I read about it (Jeff Jewitt I think) and tried it. It worked. I'm not a big fan of filled grain, but I was actually turning a pen with some real heavy open grain and I tried the plaster and it worked quite well.

Tony

Re: Somedays I should stay in bed.

#22

Re: Somedays I should stay in bed.

Rob Lee

Derek -

I feel your pain...

I was fitting crown molding for window headers last weekend, and only mis-cut about 25% of the total cuts...

I rationalize the errors by noting that my chop saw was 100' away from where the installation was taking place... and that there were inevitable distractions between measuring, and cutting.... you know... stopping to feed the chipmunk, talking to the neigbors, watching a boat go by etc....

Perhaps you could make a similar rationalization.... having to turn the shrimp on the barbie, catching up on the rugby scores etc.....

;) :D

Cheers -

Rob

Re: Somedays I should stay in bed.

#23

Re: Somedays I should stay in bed.

Derek Cohen (in Perth, Australia)

I was fitting crown molding for window headers last weekend, and only mis-cut about 25% of the total cuts...

I rationalize the errors by noting that my chop saw was 100' away from where the installation was taking place...

Rob, where was your beloved mitre trimmer?!

and that there were inevitable distractions between measuring, and cutting.... you know... stopping to feed the chipmunk, talking to the neigbors, watching a boat go by etc....

Perhaps you could make a similar rationalization.... having to turn the shrimp on the barbie, catching up on the rugby scores etc.....

mmm ... let's see ... Steely Dan was on the hifi ... a herd of wildebees stampeded through the shop .... and the barbie exploded, shot 20 metres inthe air and sent shrimp in all directions .... naah, nothing out of the ordinary ... just can't explain the loss of concentration.

Regards from Perth

Derek

Re: Somedays I should stay in bed.

#24

Gee, Rob *LINK*

Bill Houghton, Sebastopol, CA

and there are some pretty nifty tools to help with that, too (see linky)... :D :D

Bill, who only ever makes mistakes when he's awake


Other useful tools at leevalley.com too

Re: Somedays I should stay in bed.

#25

CHOP SAW!!  right here on the hand tool forum

Bill Tindall

Crown molding- the one woodworking task where it HELPS to be dyslexic.