New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Handplane repair

Posts

Handplane repair

#1

Handplane repair

David McDonnel

A Good Neighbor, knowing I was a woodworker, brought over a milk crate with several derelict handplanes in serious disrepair. A friend of his was disposing of them and he diverted them to me. Four old Bailey's in bad shape and a bedrock 603. No blades, chip breakers or lever caps on any of them. I have a few old stanley planes from which I can steel the blade and lever cap. The 603 cleaned up okay and I went to put a front knob on from the milk crate.............. arrrrrr...... the hole in the body is stripped out big time! I thought about drilling and tapping it to 1/4 - 20 but it's too wallowed out for that next up is 5/16 and I think the casting has plenty of meat to accommodate. Then I'd make a rod by welding a 5/16 thread on the bottom and a #12 piece on top to accommodate the proper knob nut.

That's my idea to make this a user plane. any better ideas?

Mac

Re: Handplane repair

#2

Re: Handplane repair *LINK*

anotherBob

Heli-Coil...? Never used them, just remember them recommended. Might be a whole lot safer than welding CI.


One Heli-Coil source

Re: Handplane repair

#3

The problem witha heli-coil...

Scott Burr

Stanley used crazy thread sizes. Maybe with the soft ironof the plane, one could screw a tote or knob shaft onto a HC and then run that into the planes bed. Back it shaft out and bingo!?!

Re: Handplane repair

#4

Re: The problem witha heli-coil...

anotherBob

If there is enough meat there to tap to 5/16, it sounds like it would be good, and be able to have a "standard" size thread in the bargain too. I'd prolly use a dab of JB-Weld for insurance too.

Re: Handplane repair

#5

Moses Yoder

Re: Handplane repair

Moses Yoder

I don't know a whole lot about welding, but it seems like you could fill the hole with stainless steel rod weld, then drill and tap. The stainless steel rods my dad uses weld really nice.

Re: Handplane repair

#6

He's not talking about welding the cast iron...

John in NM

Just a bit of 5/16 stud on the end of a knob post. I'd be tempted to try what Moses is talking about, except I'd be a bit worried about warping the sole. Maybe with a tig and nickle rod....

Re: Handplane repair

#7

Epoxy is your friend

Bob Hackett

I would just take a standard factory rod that holds the front knob in place and epoxy is permanently into place. I say permanently but anything epoxied can easily be reversed with heat.

Welding or brazing is a last resort for something like this as far as I`m concerned as I`m a "hit it with the smallest stick that results in the desired effect" kind of guy.

Bring a torch or electrode into play and you crank re-japanning at the very least into the mix. At worst you can get warping,cracking and any number of other deal breaking events taking place.

Sorry Moses,but stainless would be totally inappropriate for use with a cast iron plane IMO. Besides being hard to drill and thread properly it just has more minuses than pluses in this application. Braze would be my choice for a metal filler but there are so many other options that are far less damaging to explore first.

As far as Helicoils go,there`s a superior product (it`s staked in and will never back out like a Helicoil can) called a Keen-sert. Nearly all the repairs I did like this in an industrial environment were done with Keen-serts. One of the other great selling points about a Keen-sert is that you use standard drills and taps to prep the repair and if you`re careful you don`t even need the staking tool to anchor them.

Helicoils require special taps,installation tools and are not anywhere near as reliable as a Keen-sert. Try drilling a botched Helicoil out if you really want a challenge. Man I hate Helicoils!

Re: Handplane repair

#8

Bob speaks truth!

Joe Rogers, Northern Virginia

Re: Handplane repair

#10

I agree with derek...

David Weaver

keep those old castings around for a lap of some sort. They're nice and soft, easy to work and lap flat and easy for diamonds to sink in.

Re: Handplane repair

#11

C'mon guys

Neal in San Jose

We're talking about a Bedrock, here. Is a '57 Chevy just an old car? I think a user Bedrock is worth a little more effort than a dirt-common #3.

Re: Handplane repair

#12

Re: Handplane repair

David Weaver

I don't know...I sort of see "no blade, no lever cap, no chipbreaker" and i don't know what generation of bedrock it is, but with a stripped casting and none of those things mentioned, it could actually be worth near nothing as unless the tote was sparkling clean with a decal on it.

It might be a bit short for a diamond hone, though. Maybe a diamond hone for the kitchen!