New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Bugs in clamp

Posts

Bugs in clamp

#1

Bugs in clamp

Bill Houghton, Sebastopol, CA

I picked up a handful - big handful - of handscrews this last weekend, in varying condition. This one looks to have been invaded by various species of wood-boring bugs:


Not all of the black dots visible in the picture are bug holes, but many of them are.

I am thinking that my best approach is to put it in the freezer for a couple of days. But before I begin the negotiations (and the plastic wrapping) necessary to do that - is this likely to be effective, and is there another choice?

Re: Bugs in clamp

#2

Re: Bugs in clamp

Dale Stansbery

You could heat it to 160 deg in the oven for a day, but you'd probably have to take your wife out to dinner to get away with it. If you put it somewhere over a clean surface, you can monitor it for a time for any frass piles. In all likelihood the bugs are all gone already anyway.

Re: Bugs in clamp

#3

Jesper, Denmark

Re: Boracol

Jesper, Denmark

Dinatriumoctoborate tetrahydrate i water/glycol solution. Probably sold in the US under a similarly sounding trade name.

Not specially toxic to humans once the glycol has evaporated.

Re: Bugs in clamp

#4

won't work in this case

Bill Tindall

One has to get bugs to this stuff, or it to the bugs, which in this case are buried deep within, or more likely long gone.

Most would recognize this stuff as common borax.

Re: Bugs in clamp

#5

agree entirely-  But......

Bill Tindall

The critters that made the holes are most likely long gone. But, if you are seeing fresh piles of sawdust produced by active mining then the oven is a way to go for small objects like these. I can't see any rational objection to treating them there.

However, many ovens will not control at temperatures much below 200 degrees. At too high a temperature the wood will quickly dry from its current state and the end grain ends of these clamps may crack.

Dousing the infested wood with lacquer solvent works. The fumes get them.

I have not tried the following but it seems it should be effective. Seal wood in plastic bag with moth balls. The fumes will get to where they are at and kill them.

Re: Bugs in clamp

#6

Re: Bugs in clamp

Larry Barrett

If small enough and just wood, no metal, a quick trip in the Microwave (30 sec or so) will likely do the trick.

Re: Bugs in clamp

#7

Peril in that route..

Bill Tindall

I have been banned from the family microwave after the second episode I have used one to dry test samples for a quick moisture estimation. The problem is that some wood pieces will contain small regions that are especially good at absorbing microwave energy. These regions will char, releasing vast quantities of smoke. All that may be evident from the outside is a small fumarole. Inside will be a charred pocket. Well, also outside will be a kitchen filled with smoke.

Apparently it is just fine to fill the kitchen with smoke because the boiling potatoes went dry, but not with wood smoke, reserved for the fireplace when I forget to open the damper.

Re: Bugs in clamp

#8

Do you have a vaccume pump?

Phil Joines

Re: Bugs in clamp

#9

Re: Peril in that route..

Larry Barrett

Yes, wood can heat up quickly. That is why I suggested about 30 sec.

I have not smoked any, so have not been banned from kitchen, so far.

I have used this method to bend slats for chairs. Better than steaming, or soaking in hot water for this purpose. The heat is what does the trick.

Re: Bugs in clamp

#10

Re: Peril in that route..

Dale Lenz

test

Re: Bugs in clamp

#11

How do you bend slats in a microwave?

Pam Niedermayer - Austin, TX

Wet, form, and dry?

Pam

Re: Bugs in clamp

#12

Re: How do you bend slats in a microwave?

Larry Barrett

I have made several "Alexander" style chairs (see MACFAT http://www.greenwoodworking.com/ ). The slats for these chairs are added after the rest of the chair is assembled. The slats start as green wood, are planed to final thickness (about 3/16" or so, depending on your mortise), and then sit around for a day or two while the rest of the chair is assembled. So when you get to this stage the slats are all ready to go, but must be bent and slipped into the mortises.

One way is to soak the slat in hot water for a few minutes. The problem with this is that the slat swells a little, so it is hard to fit back in the mortise. I found that putting the slat in the microwave for a short time solved this problem. The wood is pretty hot when it comes out. You just flex it a bit over your knee, then pop it into the mortises. Always a surprise that a thin slat can take this stress but I have never had any failures with rived wood.

Re: Bugs in clamp

#13

Jesper, Denmark

Re: Function.......

Jesper, Denmark

The borate penetrates the wood somewhat, saturating it part way. When the larvae chew their way in or out, they die.

Re: Bugs in clamp

#14

Got it, thanks, very good process.

Pam Niedermayer - Austin, TX