New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Update on The Blade.

Posts

Update on The Blade.

#1

Update on The Blade.

Derek Cohen (in Perth, Australia)

Here are a few teasers ..

It is going to be a BIG plane - but calling it a "jointer" would be only partly correct ..


What the blade/cap iron is going to look like (single iron, 50 degree bed). I had to laminate the body as the (ex-roof truss) was only 3" wide. Oh - Jarrah (what else) ..


And the tote, which is still being shaped ...


Regards from Perth

Derek

Re: Update on The Blade.

#2

Re: Update on The Blade.

Bill Houghton, Sebastopol, CA

I assume you're clearing out a space under your bench where the young lad who will help move that critter across the wood can sleep, unless you're planning to use horses.

Re: Update on The Blade.

#3

Re: Update on The Blade.

Derek Cohen (in Perth, Australia)

This has multiple uses.

I can hook a sail to it and go windsurfing.

If I build another, they would make great shoes for the snow in Perth.

Not to worry about the effort involved in use - I have trained a team of wombats to pull the plane using a minature harness that attaches at the levercap.

Regards from Perth

Derek

Re: Update on The Blade.

#4

Re: Update on The Blade.

Jerry Nicholson

I would think Tasmanian Devils might be a better choice for a draft team. Might be harder to train though.

Jerry

(who lives in Kansas and has never seen a Wombat or a Tasmanian Devil)

Re: Update on The Blade.

#5

Tasmanian devils

Bill Houghton, Sebastopol, CA

Clearly, you watched far too many cartoons in your youth.


img

Re: Update on The Blade.

#6

Moses Yoder

Re: Update on The Blade.

Moses Yoder

Why use a lever cap instead of a wedge? Perhaps because you had a lever cap laying around? Seems like a wedge would hold the iron better. Another amateur question, hold did you fill the groove in the iron; it looks like brass, but how is it stuck in there? And I just have to ask, although it is not April 1 it is still April, is this some sort of April Fools joke? Or perhaps you didn't have it ready for April 1?

Re: Update on The Blade.

#7

Re: Update on The Blade.

Derek Cohen (in Perth, Australia)

Why use a lever cap instead of a wedge? Perhaps because you had a lever cap laying around? Seems like a wedge would hold the iron better.

Hi Moses

Originally I planned to use a wedge. Indeed, the pictures you see are of Mk2. Mk1 had mortices for a wedge.

Then I examined the blade carefully and discovered that the wedge-side of the blade was not coplanar -probably because of all the work done to lap it flat. This meant that a wedge could not provide even pressure along its length.

At the same time I recalled the lever cap that Peter had given me, and this seemed to me to be the answer since the lever cap would not be affected by a blade lacking a coplanar surface. Note that the back of the blade - the side that rests on the bed - is both flat and coplanar. Without that the blade would rock.

Another amateur question, hold did you fill the groove in the iron; it looks like brass, but how is it stuck in there?

The blade is designed to use a cap iron. While it could be used without a cap iron with a wedge, the only way I can work with this blade was to use a lever cap. And the slot would made it impossible to use a lever cap without a cap iron. I didn't want to use a cap iron as I believed that the blade was thick enough. I did, nevertheless, make a cap iron (out of some of the hardest brass I have ever come across). I did not like the effect. So I chose to infill the slot. I have done this before...

A 3/16" Hock blade used in a jointer ...


I simply filed a piece to fit fractionally oversize, then peened it in. A little epoxy was added to the rear for good measure (as the 1/8" brass is not as thick as the blade).

And I just have to ask, although it is not April 1 it is still April, is this some sort of April Fools joke? Or perhaps you didn't have it ready for April 1?

Believe me I thought of it! :) But, no, it is real. And I'm hoping that it will get good use.

Regards from Perth

Derek

Re: Update on The Blade.

#8

Re: Update on The Blade.

TomD

I have a new friend who sells those winch units they use on 4x4s. Apparently the slick set-up is a tow line that is made of dynex, a soft braded material of super strength. Looked ideal for towing a really wide plane through beams.