New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

How to make a weather indicator?...

Posts

How to make a weather indicator?...

#1

How to make a weather indicator?...

John Aniano in central NJ

Hello All,

Wondering - does anybody out there know how to select the tree and make one of those wooden "weather indicators"? You mount them outside, and if it points up, the weather will be good, down, weather bad. The one I had was from Lehman's catalog and they said it was made of Balsam fir. Mike Dunbar thought they were a good indicator for successful steam bending of Windsor chair parts.

Any of the FoxFire book entries on how to make one of these? Any other ideas? Just looks like a section of the tree and branch with the bark removed, but maybe there is more to it than meets the eye.

Picture is from Lehman's website and is for illustration use only.

Thanks,

John

P.S. Yes, I know they are only a few bucks, but I thought I'd ask the collective wisdom out there anyway...


Re: How to make a weather indicator?...

#2

The ones I've seen described...

Bill Houghton, Sebastopol, CA

use a length of some flexible wood with some of the side wood glued cross-grain with a flexible glue. As the wood glued cross-grain expands/contracts with relative humidity, the assembly bends one way or another.

The one pictured may use the fact that tension wood will move along the grain more than regular wood.

I can't recall if Foxfire pictured one of those, and my Foxfire books are boxed up in the attic in preparation for tearing into the room they normally live in.

Re: How to make a weather indicator?...

#3

Stephen Shepherd

Do you mean the Rittenhouse hygrometer?

Stephen Shepherd

Re: How to make a weather indicator?...

#4

Moses Yoder

Re: How to make a weather indicator?...

Moses Yoder

I have one made out of a rock. If it's wet, it's raining, and if it's dry it aint.

Re: How to make a weather indicator?...

#5

Re: The ones I've seen described...

Kevin French, Henniker, NH

From Wikipedia

A weather stick is a traditional means of weather prediction used by some Native Americans. It consists of a balsam fir or birch rod mounted outdoors which twists upwards in low humidity and downwards in high-humidity environments. These sticks were first used by the Native Americans of the American northeast and the Canadian east and southeast, who noted the behavior of dry branches prior to the arrival of weather changes. The weather stick is a rare example of a weather prediction tool which predates the mercury barometer

And from eHow.com

Instructions

things you'll need:

14 inch balsam fir stick

Penny nails or tacks

Block of wood or bark as base plate

Get what you need for every

project at HomeDepot.com

Find Balsam Fir Trees

1

Look for a grove of balsam firs. Find a place where saplings are growing, and pull up a few at least 14 inches long.

Weather sticks are balsam fir saplings that have been stripped of their bark and dried. Balsam fir trees tend to grow in sugar maple groves.

2

Strip the bark from the saplings. This will allow the weather stick to dry. Because the wood is fresh, it will take a while to dry out adequately.

3

Nail or glue the sapling to the base plate so that it is attached and will be able to support the weight of the weather stick.

4

Mount the base plate at a desired location.

5

It might take a while for your weather stick to acclimate to your specific climate. Monitor how the stick changes, rising or falling.

Read more: How to Make a Vermont Weather Stick | eHow.com http://www.ehow.com/how_5616400_make-vermont-weather-stick.html#ixzz1IFKsnRIY

Re: How to make a weather indicator?...

#6

Re: The ones I've seen described...

TomD

Just speaking of glue in it's structural apps, should anyone care at some point. First the way I have seen the two piece ones built, the glueline is pretty much at the neutral axis. Second if the parts couldn't bend, or the glueline otherwise came under shear load Then maybe a flexible glue would be a good way to go so long as the elongation expected is actually within the glue's ability to give. If it is not (most cases), then the harder/more creep resistant glue will have a better chance of surviving. If one just wants a flexible glue because of flexing in the piece, normally a harder glue is better, and the glueline will be thin enough that it will not seem hard, just as aluminum foil appears flexible in film form.