New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Coupla diamond sharpening questions

Posts

Coupla diamond sharpening questions

#1

Coupla diamond sharpening questions

Frank D. in Montreal

Hi everyone,

I searched the hand tools forum but can't seem to find an answer to my questions.

1. What's the best way to cut up an old cast TS top? I read about hacksaws...would a hand grinder with a cutoff wheel be OK?

2. I read that many who use cast iron have the surface blanchard ground. I'm not afraid of machine shops, but could I avoid this step and flatten 3 sections by rubbing them together with carborundum (I suspect coarse diamond would contaminate them and make them useless)?

3. I'm not sure I want to start honing all my blades by hand, simply because I have a sytem that lets me give a precise camber to blades by applying pressure at certain points of the blade for a certain number of strokes. I'd probably have to redo the math for the number of strokes, but I doubt I could get a half-thou camber by hand. Should I use a different sharpening jig for each diamond grit/plate? (I suspect yes)

Thanks

Re: Coupla diamond sharpening questions

#2

My experience with cast iron

Steve Elliott

Frank,

I can�t help with the question of cutting up the tablesaw top, having only cut cast iron with a hacksaw, quite slowly.

Most tablesaw tops are Blanchard ground. The pattern of crisscrossed circular arcs you see is evidence of that. It doesn�t guarantee the flatness of the surface, but you can check that with a straightedge or surface plate. I�ve used a coarse waterstone to improve the flatness and surface of a cast iron plate and that worked, so I imagine that carborundum would also work. After the waterstone treatment the plate produced a less-sharp final edge (using fine diamond) for a few sharpenings, which I suspect was the result of embedded grit that eventually wore down. I might not have noticed it if I hadn�t been doing sharpness testing at the time.

Although I have several cast iron plates my sharpening routine only involves one, for the final 1-micron-or-less polishing. Sometimes I use the other side of the plate for 3 micron diamond, which cuts much faster, but usually I go back to grinding on my Tormek right down to the edge instead of using coarser diamond. That eliminates the issue of transferring grits. Using a fixed diamond plate is another solution to eliminate transfer.

Instead of one jig for each plate I�d suggest either using fixed diamond for the coarser grits or using a jig where the roller doesn�t ride on the abrasive surface.

Re: Coupla diamond sharpening questions

#3

Re: Coupla diamond sharpening questions

Bob Hackett

What I cut my cast iron with was a diamond blade I bought at one of the big box stores and put in a worm drive skillsaw.I had originally bought the blade to cut stone counter top material and it worked fine for the CI and then returned to stone duty with no ill effects.

If I had to flatten a CI plate I would scrape it rather than abrade it.Scraping goes much faster,offers more control and precision and is not that difficult to do on CI.

Re: Coupla diamond sharpening questions

#4

Re: Thanks

Frank D. in Montreal

Thanks Steve,

That was very helpful. And now I know what blanchard grinding is (in my mind it was more polished)...I'll probably just flatten the plates a little if needed.

Re: Coupla diamond sharpening questions

#6

flattening requirements

Bill Tindall

Keep in mind that the plate only needs to be flat over the surface area of what is being abraded. Perhaps some jig device would have more stringent requirements but for free handing it is hard to imagine any piece of ground cast iron not being flat enough. The inclination will be to worry about flatness and surface quality of the plate way more than is necessary.

Cast iron cuts like butter with a metal cutting band saw. It would seem likely that you could find some shop willing to slice up a top for little cost. We had numerous cast bars cleaved in half for little cost.

Re: Coupla diamond sharpening questions

#7

PS

Bill Tindall

Last night I cut the web out of an angle plate using an abrasive cut off wheel on a 4" angle grinder. It was slow, things got hot and I wore out a wheel. Should I need to do it again I will hack saw it.

Re: Coupla diamond sharpening questions

#8

Re: Thanks

TomD

I like a smooth finish the media won't get lost in. The part I have is really smooth, but I don't know how it got that way. I have a surface grinder in the shop, but unfortunately haven't found anyone who will part with a chuck for it at a price I can afford. I imagine a few rare earth magnets would probably work for the small stuff. Actually I have a KO lee,but it works for small jobs.

http://www.youtube.com/watch?v=sesxx-U_0FU

Re: Coupla diamond sharpening questions

#9

Re: Thanks

Frank D. in Montreal

So...is that an invitation?

:D

Re: Coupla diamond sharpening questions

#10

Re: flattening requirements

Frank D. in Montreal

Thanks Bill,

I'll keep that in mind. I'm certainly not too anal about flatness, flat enough being the goal. I use a bowed DMT diamond stone to flatten my waterstones and I make do fine with it.

Re: Coupla diamond sharpening questions

#11

Re: Thanks

TomD

I thought I answered this. Sure if I can help. Actually, a shaper, I have two, is perfect for this, it will surface without swirl. and perfectly flat. They use them in various sample prep functions where a scratless surface is required to minimize stress raisers. Mine will only do 7".