New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Chipping on leading edge of lever cap

Posts

Chipping on leading edge of lever cap

#1

Chipping on leading edge of lever cap

Bill Houghton, Sebastopol, CA

The jack plane I'm cleaning up has some small chips from the leading edge of the lever cap - maybe 1/32" deep in several places across the width. Is this meaningful? Should I file it smooth again and fair the leading edge to a curve? Or is it cosmetic.

I've got a Millers-Falls lever cap soaking in the vinegar solution, in case y'all say it's hopeless, but I'd rather not make this a frankenplane.

Re: Chipping on leading edge of lever cap

#2

My advise

Bob Hackett

If it ain`t broke don`t fix it.

Use the plane first and see if it jams because the shavings are getting caught in the chipped lever cap.If not,Bob`s your uncle.If so file as little as possible to smooth it.

Re: Chipping on leading edge of lever cap

#3

I agree.

Bruce, a MN Galoot

I have two planes like that, a #4 and #5, both likely the result of using the lever cap to loosen the screw on the iron.

If it doesn't interfere with performance, just grin and bear it. I was going to say, "if it ain't broke," but it already is. :D

Re: Chipping on leading edge of lever cap

#4

Actually, yes, Bob was my uncle

Bill Houghton, Sebastopol, CA

on my father's side.

Thanks, Bob (so, do you have any nephews/nieces who can say "Bob's my uncle?") and Bruce. I'll see how it works.

Re: Chipping on leading edge of lever cap

#5

Re: Actually,

Bob Hackett

All my nieces and nephews can say "Bob`s my uncle",and usually do when I`m standing within ear shot just to see me smile. :D

Re: Chipping on leading edge of lever cap

#6

Re: Chipping on leading edge of lever cap

David Weaver

I have the same thought as the other guys. Unless there is a gap between the iron and the chipbreaker, it's really not going to interfere with anything unless you're one of the few people who actually sets the chipbreaker right on the edge of the iron to increase the effective angle of the cut and actually break chips (like within a few thousandths of the edge).

I don't know of many people who do that. Warren probably knows what effect they'd have in that instance.

Putting a tiny back bevel on an iron has the same effect (to me) in feel and effect cutting anything where you'd need to do that, anyway.

So, I'd ignore it if it doesn't bite you.

My favorite utility smoother is a mujinfang ebony continental style smoother. The leading edge of the chipbreaker is pretty dinged up - I guess they figure you'll file it and clean it up if you want to use it close in. I have not found the need, the front edge of the thing is still dinged up, and it's still a wonderful plane to use.

Re: Chipping on leading edge of lever cap

#7

Chipping on leading edge of lever cap

R.J.Whelan

Bill,

The other chaps are probably right about not worrying over minor dings (unless you get hairballs).

That being said, my OCD usually mandated either finding a replacement, filing smooth, or applying a bead of bronze and filing and polishing smooth (looks kinda pretty contrasted with the steel).

Once again, I've said much and contributed little.

Happy holidays ........... rj

Re: Chipping on leading edge of lever cap

#8

Re: Chipping on leading edge of lever cap

Joe Mohnike

Like others have said try it if it works don't worry about it. I have used JB Weld in the past as a filler. Apply, let cure and then sand. I have one that I filled a chip apx 1/16"several years ago and it is still in place and the tool gets used a lot.

Joe M.