New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Hanging wall cabinet

Posts

Hanging wall cabinet

#1

Hanging wall cabinet

Edward in Vancouver

I've pretty much finished my christmas presents and am now planning a new project, I'd like to make a hanging tool cabinet, maybe for the summer.

My bench sits against the south wall of my garage underneath a 4' window, and I have most of my small tools stored in a LV "gerstner" style machinest's chest that sits on a trolley to the immediate left of my workbench, a foot away from the right end of my bench is the door.

I came up with some kind of measurements: About 13" deep, about 32" high, and about 29" wide, closed. There's two things I insist on my hanging chest providing, 1) it must house my current toolchest, and 2) it must be totally lockable. And it must hang from a french cleat, which would be an integral part of the cabinet carcass.

I've gone over a few designs, single door, double doors, doors with lips, and inset doors. Double doors with lips present some challanges for locking, but lots of room for hangings stuff; inset doors would be the easiest to lock. A single door with the hinges on the left would be the easist to build, but if I ever moved and had the chest hanging on the right of my bench, would be problematic.

How would I go about locking double doors with lips--that is doors that look like a shallow tray?

Assuming I ran a full length of piano hinge on the doors, how much wieght could such a door take?--

My library has coughed up F.W's "workstations and tool storage" but none of the articles describe locking up the doors, and of course I've drooled over Studley's chest which actually is a very simple single door hanging chest(on the outside at least...)--with what appears to be a very elaborate lock on he left side of the door.

Since my LV chest is qswo (completed about two years ago) I'd like to make the hanging chest the same, probably frame and panel door(s) and half blind dovetails on the bottom and top of the case.

But how to lock up the sucker? Any help is appreciated

Thanls, Edward

Re: Hanging wall cabinet

#2

Only limited by your imagination

Bob Hackett

I`ve seen locks for this type of thing that range from simple paddle latches turned by a key where the paddle engages a groove in the case to a pin lock that comes up from below to engage a hole,to a sliding strap on the side that prevents the door from opening.

also having a lip on the edge of one door that the other door covers means you only have to have a lock on one door in order to secure the cabinet

Keys range from high security,to rare earth magnets to wooden keys,to combination locks.

A friend suggested I stop looking at "locks" and start thinking about "door limiting devices".Excellent advice that.

Re: Hanging wall cabinet

#3

Re: Hanging wall cabinet

Dominic in Buck's County PA

Here's what I came up with:

Tool cabinet doors

It's about 52" - 54" wide (can't remember exactly) x 42" tall x 13 1/2" deep.

Tool cabinet doors

The left door is secured via a has that engages an inset brass piece on the shelf. Then the right door is closed and secured via a lock. Notice the brass bound area on the right door frame? The lock sits behind that.

Photobucket

There is a lip fixed to the right door that covers the reveal between the two doors. I inlayed a piece of walnut in there to simulate the seam and give it a better look.

Re: Hanging wall cabinet

#4

Moses Yoder

Re: Hanging wall cabinet

Moses Yoder

I made my doors deeper with a fold out tray inside them. With a 29" wide cabinet I suggest 2 doors or the weight of tools hanging on the door will put excessive force on it. I would make a pair of doors with a frame on the back to build a tray like you describe then I would countersink a lock in the left door that locks it to the carcase. Then you would swing the right door shut and have a lock that locks it to the left door. National Lock has a large variety of locks, but I think you could do this with standard cylinder locks. They make a cylinder lock with a hook on the cam which you might need for the left door then just a standard cylinder lock for the right door with a cam that catches on the left door would work.

Re: Hanging wall cabinet

#5

How effective does your lock need to be?

Bill Houghton, Sebastopol, CA

Are you protecting against casual use of your tools, such as a child too young to understand; or serious crime prevention? If the latter, you might consult a locksmith.

Re: Hanging wall cabinet

#6

Moses Yoder

Re: How effective does your lock need to be?

Moses Yoder

Several thing to consider. 1) If the box can just be lifted off a french cleat, what is the purpose in locking it? 2) If someone is desperate they can always give a wooden box one whack with a sledge hammer and open it like an egg. These are reasons why my box has no lock on it. I suppose if you are really into theft proofing your tools, you could buy a Browning gun safe and put shelves in it.

Re: Hanging wall cabinet

#7

Hey, Wait one minute...

Scott Burr in Ben Lomond CA

My Gawd Dom, After all this time and you still haven't filled that thing up yet!?!

:D

Re: Hanging wall cabinet

#8

Re: Hanging wall cabinet *LINK*

charlie belden

Deep usually means Stuff Behind Stuff. That means having to Move Stuff To Get To Stuff. And if you have to move stuff - where I you going to put it while you get out the stuff you need? That means either leaving the moved out of the way stuff back - and having to move it again when you put the stuff you got out to use back - and then put the stuff back in front of the stuff you just put away . . . . Then there's the Out of Sight, Out of Mind thing. Stuff behind stuff gets hidden by the stuff in front of it. That can mean playing Is It Behind Stuff #1? And let's face it, if a shelf is deep enough to put things in front of other things - we'll put things in front of other things - even knowing that means moving stuff to get to stuff. Single Layers Simplifies Stuff Finding - Using - and Putting Back.

Think of your above counter kitchen cabinets. Pick one and go exploring. I'm betting you'll find stuff in the back you forgot you even had. If you want to see stuff, get to it quickly and easily and be able to put it back - Deep is not where you want to go.

But if you split the Deep up into two parts, each part is less deep. So think Storage In The Doors. Cuts down on the Deep problem AND almost doubles your effective wall storage space. To support the weight in the doors you'll need to use piano hinges. They present an installation challenge since they have no adjustability - but there are some tricks to increasing successful installation. As for raised panels - they're dust catchers and break up the look of the wood in the panels. It's a TOOL Cabinet you want, NOT a pretty kitchen cabinet right?

The other thing to keep in mind is Things Will Change. What you plan on storing in the cabinet today may not be what you will want to store in it later. And where you put things in the cabinet (and doors) today, may need to be moved in the future. SO - think Modular storage units - that can be rearranged or modified down the line some time.


Modular Wall Haning Cab

Re: Hanging wall cabinet

#9

Re: Hanging wall cabinet

Edward in Vancouver

Thanks for all of your replys gentlemen, and thanks for the pics. It'll probably take me until March to figure our how I want to lay this thing out, now tht I have so many options.

1) The lock should be a "15 min" lock, meaning that after 15 mins someone (unbeknownst family members looking for a pruning saw or paint can opener) will either give up or smash the thing to smithereenies.

As a decoy, I usually have my "garage sale specials" hanging on a wall not too far away. Perhaps I should keep the hammers locked up?

2) It will hang from a French cleat, but will be screwed into a stud from the inside.

3) The "modular" approach is starting to make a whole lot of sense. Perhaps in the distant future a "twin" cabinet will be made.

I remember working in one Hotel where the pastry chef kept his "secret" recipies in a locked drawer underneath a massive marble topped table. I couldn't pick the lock, nor could I remove the drawer unit fom the frame, but.... with the aid of a car jack and a few milk crates and plywood, I raised the marble top up a few inches, fished the book out with a pair of tongs, and ran off to the photo copier before something nasty happened. Pastry Chef gave me holy heck next day, he wasn't angry that I copied his recipies, but because I wouldn't tell him how I broke in......

Re: Hanging wall cabinet

#10

Moses Yoder

Re: Studley

Moses Yoder

If you look at the Studley tool chest you will see frames with tools hanging on them that fold out of the way to get to tools behind them. I modeled my tool chest after this idea, not nearly as nice of course, but the idea is the same. I have frames behind the door that fold out of the way with tools hanging on both sides, and I also have fold out frames in the doors. I think my box is about 16" deep if I remember right.