New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Rookie Veneering . . .

Posts

Rookie Veneering . . .

#1

Rookie Veneering . . .

steve mackay

30's dresser followed LOML home this weekend. The veneered top is shot. Not pealing, shot. Would we take pity on the rookie and suggest an on-line primer for replacing ? Not to actually DO it but just get "in the mood". I'm assuming it can be done by mere mortals such as I.

Steve (giving dresser the hairy eyeball)

Re: Rookie Veneering . . .

#2

Re: Rookie Veneering . . .

Bill Houghton, Sebastopol, CA

My less-shop-competent, though highly detail-competent, did a lovely re-veneering job on a night stand; you can, too.

Fearing that I'm going to come off as obsessive on libraries (I do bring it up a lot, I know), if you live in a town with a half-decent library system, there will be books on veneering. My county system has three (I just looked) exclusively on veneering, and it's often covered as one subject in survey books.

Just like online, books can be dreadful or great, depending on author and editor; but you should check out what your library has.

When I read your title, my immediate thought was, "how will you hold the rookie still while you veneer him/her?"

Re: Rookie Veneering . . .

#3

Leo Cuellar

Contact cement!:)

Leo Cuellar

Re: Rookie Veneering . . .

#4

I want pictures

James Watriss

Can give better recommendation with an idea of what you're dealing with.

Re: Rookie Veneering . . .

#5

Re: I want pictures

steve mackay

I scraped off what was loose so theres no way back. :D


Re: Rookie Veneering . . .

#6

scott grandstaff

Bummer

scott grandstaff

Wish you hadn't done that. You could have saved it easier than starting over, but oh well.

I did a similar dresser recently. Mine was worse than yours, certainly. The top was caved in, broken!

Not a single surface of veneer was intact either. Chips, cracks, edges ragged out. The usual way you find these and why they always come cheap to free. Mine was on its way to the dump.

Nobody says its easy. This job scares the hell out of 99% and more.

The one I did was even worse with having to reinforce every drawer/dust frame to take more weight.

yours Scott

PS I just tried the regular image html code because there is another picture of the bureau, and it wouldn't work??


img

Re: Rookie Veneering . . .

#7

WOW ! . . .

steve mackay

So how do we start getting the old veneer off ?

Re: Rookie Veneering . . .

#8

scott grandstaff

Re: WOW ! . . .

scott grandstaff

So how do we start getting the old veneer off ?

You don't, any time you can avoid it.

You repair what you have if at all possible. And it is practically always possible in the condition you found them in.

Taking all the veneer off is just like taking all the old finish off a piece of furniture down to bare wood. If you have to, you have to, but otherwise its always, always, better (and 100 times easier) to restore what you already have. The concept of "skinning" work was invented by people who sell supplies for the job. It is never easier or quicker, believe me.

The job of restoration is quite challenging enough, thank you.

Veneer repairs you can learn to do for almost free. It takes little more than a supply of scrap veneer, clamps, cauls and tape, and.... time.

Find matching or as close as you can get veneer. Line up the grain pattern carefully, cut your patch oversized and avoid straight lines like the plague. A straight line demands your attention like neon. Curves blend.

Overlay your curving irregular parch and trace around it. Take sharp knives, chisels and scrapers and remove the old.

Pad your replacement piece with a "caul" or scrap wood, wax paper inbetween and clamp it down, using ordinary glue. If you can't clamp it, lead bricks or very heavy weights of any kind will do.

Next day scrape it clean and blend with a little stain and/or artists oil colors and after a few tries color matching it will just disappear before your eyes.

With your top tore up that bad now, you are going to have scrape all the old veneer off the top and start over there.

Sharpen your scrapers often and go to work. I like to use 4 or 5 scrapers, using each one until the edges are gone and then re-sharpening the whole batch at once.

Do not mess with the rest though, you can still save that!

Veneering full panels means either, buy an expensive vacuum press (guaranteed success rate, but it better be at hundreds of dollars cost, and decide carefully if you are going to go into veneering full time or else you have foolishly wasted a lot of money for another dust covered box in the corner of your shop),

or begin to suffer contact cement (always hated it myself but I have seen good work done with it). You can't get the "good" contact cement anymore and even the good stuff was always lousy, IMO.

But again, I know a couple guys who are good with it, so its possible.

or try the iron-on veneer (Jury is still out). It was a popular fad once. I don't hear about it anymore though, so that makes me uncertain.

Or........ master the ancient art of hot glue hammer veneering.

This is the fully traditional way. A learning curve for sure, but not so expensive to start.

There are 88 million websites already established on veneering. Take a Google stroll through any number of them. But watch out for the dozens of heavy sales pitch sites telling you how easy life is, if you only BUY something. Something they conveniently have for sale at top dollar, by the way.

yours Scott

Re: Rookie Veneering . . .

#9

Thank you . . .

steve mackay

Now I know where I'm heading. Not a pretty horizon but out there none the less.

Please fasten my seat belt and put my tray table in the stowed position, here we go !

Re: Rookie Veneering . . .

#10

Ellis Walentine

About photos

Ellis Walentine

Scott, when you upload a file to your message, our system gives your file a unique name, so there's no danger of image collision.

Ellis

Re: Rookie Veneering . . .

#11

Vacuum press

James Watriss

I think it might be easier, for the sake of this project, to look into one of the cheap little vacuum pumps from Woodcraft. My first instinct was to vacuum bag the veneer on, just because of the curve over the front edge.

But there's a whole learning curve involved, so maybe I'm just stirring the pot.

Re: Rookie Veneering . . .

#12

Re: Rookie Veneering . . .

ThomD

Are you going to hammer veneer it, it is pretty easy, quick no irreversable steps except cutting the wood.

As far as the removal of veneer is concerned, is it old enough to be hide glue? If so you can remove it with heat, or reaply it with head sometime by nothing more than heating it and pressing it back down with the hammer. I made a hammer out of purple heart and a brass strip. A turning project if that makes you feel better.