New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

OT- fuel filter in Ford Taurus

Posts

OT- fuel filter in Ford Taurus

#1

OT- fuel filter in Ford Taurus

Bill Houghton, Sebastopol, CA

I'm changing the fuel filter in my 2001 Ford Taurus for the first time (low mileage: my uncle gave it to me three years ago with just 17,000 miles on it; he hadn't been driving much). The manual talks about relieving fuel pressure before opening the filter.

On my Volvo, the system will bleed down enough overnight that relieving pressure is taken care of by time.

I just (6:00 p.m.) moved the Ford up the driveway to the "shop space" part of the driveway (what you do when you have no garage), and will be working on it tomorrow morning. Will the system bleed down enough overnight that I don't need to depressurize it, or does the Ford system maintain pressure for a long time?

Re: OT- fuel filter in Ford Taurus

#2

Don't count on it....

John in NM

My Saturn has a similar system and does not seem to bleed down overnight. It should be easy enough to find the pressure relief valve, its just a schrader valve with a cap like for filling your tires (or at least mine is). The hard part with my filter is getting the darn fittings apart. Remember when everything used a flare nut? Not so anymore, now they're all these fancy little plastic thingies that hold high pressure without leaking (probably because they get thrown out with every filter change). There is usually a special tool that will spare wear and tear on fingers and much cursing, but I still seem to do it the hard way.

Re: OT- fuel filter in Ford Taurus

#3

Pressure was fine

Bill Houghton, Sebastopol, CA

The system bled down just fine overnight.

I can't say the same for the clamps on the fuel hoses; those did not go fine. What Ford was thinking when it engineered clamp "clips" that required pushing a small piece of plastic in two opposing directions while also pushing the clip out in a third direction, in constricted space...oh yeah...they were thinking, "This can be done quickly on the assembly line."

Getting the clips off consumed about 75% of the time spent on changing the filter, including the time spent jacking up the car and putting blocks under the right rear wheel so I could reach the filter.

But (whew!) service life is so long on modern components that I don't have to worry for another 30,000 miles, by which time, maybe I'll have won the lottery, and will be letting the mechanics worry about how to do maintenance on the Bentley.

Re: OT- fuel filter in Ford Taurus

#4

Re: Pressure was fine

Joe Rogers, Northern Virginia

Life lesson #1 for automobile technicians. (And do it your selfers)

Automobile manufacturers don't care a bit about how hard it is to fix or maintain cars.

If the assembly can be done cheaper or quicker it is a done deal.

Production is king.

My guess is that after struggling mightily to remove the filter the new one just snapped into place. :b

Sorry for the cynicism but I've been swinging wrenches on these darn things for 30+years.

JR

Re: OT- fuel filter in Ford Taurus

#5

About that Bentley

Neal in San Jose

I heard on the mail this morning that they are being recalled. The retraction device on the hood ornament is prone to rust, and the hood ornament doesn't retract right in an accident.

Re: OT- fuel filter in Ford Taurus

#6

Wrenching

Bill Houghton, Sebastopol, CA

Part of it, of course, is learning curve. I wrenched on VWs for a while, back in the air-cooled days; and several years ago, when we were getting ready to sell my mom's 1971, I got the valves adjusted in the time it took my (older) brother to organize whatever maintenance job he was doing on it.

He was surprised and ever-so-slightly miffed when I surfaced, asking, "What shall I do next?" Sibling rivalry is forever, although that's digressing (one of my specialties).

And, yes, filter installation, other than retrieving the sheet metal insert nut that had falled into the sill member due to insufficient spring pressure holding it in place, was quick. Altogether, I'd say the job used only two days worth of curses.

Re: OT- fuel filter in Ford Taurus

#7

The proper British solution to that problem

Bill Houghton, Sebastopol, CA

would be to run an oil line from the motor to the hood ornament retraction mechanism, to keep it lubricated. As a side benefit, it would ensure oil puddles on the garage floor, in case the oil seals are not doing their proper job of leaking slightly.

But now that Bentley's German-owned, I predict they'll use a solid lubricant that costs $998 to replace when it finally fails at 150,000 miles.

Re: OT- fuel filter in Ford Taurus

#8

Rolls-Royce retracting hood ornaments

Bill Houghton, Sebastopol, CA

Apparently, the hood ornaments on Royce autos get stolen so often that they now retract under the hood whenever you lock the car, leaving only a wee trap door through which the ornament will appear when you unlock the car. I guess for more than $300,000, you expect this sort of feature.

And to think, I'm still kind of pleased with our radio antenna disappearing into the trunk when I turn the radio off (we tend to hold onto our cars for a long time, so we get excited by things, like central locking done with a little radio sender thingie, about 10-15 years after everyone else has gotten used to them).

Re: OT- fuel filter in Ford Taurus

#9

Re: The proper British solution to that problem

Joe Rogers, Northern Virginia

"But now that Bentley's German-owned, I predict they'll use a solid lubricant that costs $998 to replace when it finally fails at 150,000 miles."

Not to miss any marketing opportunities, Bosch is now selling replacement smoke to refill the electrical systems on the old English Bentley models with Lucas designed wiring. (It's an inside joke but funny anyway)

Joe

Re: OT- fuel filter in Ford Taurus

#10

Interesting *LINK*

Bill Houghton, Sebastopol, CA

I didn't know metric smoke would work on Whitworth electrical components.

This thread could rapidly turn into a British car disrespecting discussion...might as well go straight there - see linky below.


http://www.mez.co.uk/lucas.html