Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Powder-driven fasteners - plywood on concrete

Posts

Powder-driven fasteners - plywood on concrete

#1

Powder-driven fasteners - plywood on concrete

Bill Houghton, Sebastopol, CA

I'm putting down three sheets of plywood over a concrete slab (on top of plastic vapor barrier, and, no, I'm not putting down sleepers to ventilate it, but I am using treated ply, and the slab is on top of grade).

I'm picturing drilling for 250 tapcons (rough estimate: standard 6" on the edges, 12" in the field, which may be overkill, but should reduce squeaks), and wondering about powder-driven fasteners. I've never used them, and wonder what experiences people have with them. Are they suitable? Will the fastener set flush enough with the ply to lay a floating floor atop it? Are they a hassle to "balance," neither over nor under-driving?

Re: Powder-driven fasteners - plywood on concrete

#2

Do you have one yet?

John in NM

I was planning on getting rid of mine :D:D:D

You should be able to set them flush enough with a little experimentation. There are five load strengths IIRC, and if you're using nails with no washer you shouldn't have a problem with nails sticking up.

But.... I've never had much luck with the darn things, which is why I'm going to get rid of my driver. I can never get the nail to hold well, as the concrete tends to shatter around the nail... probably the concrete is too fresh when I'm trying to do this. Every time I've used the driver I ended up drilling and anchoring with redheads or something similar anyhow.

Re: Powder-driven fasteners - plywood on concrete

#3

Jack Guzman from Maine

Re: Powder-driven fasteners - plywood on concrete

Jack Guzman from Maine

It's not hard getting consistent results . Just take a few practice shots with varying loads and nail lengths till you get the desired result. --Jack

Re: Powder-driven fasteners - plywood on concrete

#4

Moses Yoder

Re: Powder-driven fasteners - plywood on concrete

Moses Yoder

I nailed down the bottom rail of a porch rail to a cement porch once and found they work okay if they don't hit a rock in the cement. I don't think they have much holding power though so far as holding something down because the cement does not provide much grip as it tends to shatter when the nail is driven in; it just keeps it from moving sideways. I think it would be easier to screw down sleepers and then use standard nails to nail down your floor.

Re: Powder-driven fasteners - plywood on concrete

#5

Re: Powder-driven fasteners - plywood on concrete

Jim Toews - Walla Walla, WA

Bill,

I used one to fasten sleepers to a 50 year old concrete wall in a basement I remodeled years ago. It worked great for that purpose, but it was a little loud, especially in what was essentially a cement box. After the first board I took a break and bought a pair of muff style hearing protectors. Made all the difference. I also needed to open a window and place a fan in it to remove the fumes. I do not recall any problems with heads sticking up once I found the correct strength cartridge to use, a matter of having a small pack of each strength and whacking in a nail with each until I found the right one, and then buying a box of those. I still use that old thing now and again; there are times when nothing else will do! Just my experience/opinion.

Cheers!

Jim

Re: Powder-driven fasteners - plywood on concrete

#6

Re: Powder-driven fasteners - plywood on concrete

wilbur

I looked into one when I was in the process of drilling holes for attaching 2x4's to the cinder block walls of my basement with anchors. I decided to go with a hammer drill.

In your case, I'm not sure I would want to deal with the noise from 250 discharges of .22 cartridges. With a depth stop, a hammer drill seems to offer a level of control that powder-driven fasteners don't.

Re: Powder-driven fasteners - plywood on concrete

#7

Yes, I'm leaning that way

Bill Houghton, Sebastopol, CA

I own the rotary hammer and the right size of bit already, so it should go fairly quickly, I guess. I'll just have to get out the foam pad for my knees.

Re: Powder-driven fasteners - plywood on concrete

#8

Jim in Burlington Ont.

Re: Powder-driven fasteners - plywood on concrete

Jim in Burlington On

I would head off and seek out a glue solution that would take care of making the barrier between wood and cement. If not tapcon's will go in easily with a big rotary hammer drill and a SDS bit.

Re: Powder-driven fasteners - plywood on concrete

#9

Re: Powder-driven fasteners - plywood on concrete

ThomD

+1. I have one of those power fasteners, and the one I had was useless. I think it might be a cement vs concrete thing, though considering what it is designed for, not sure how it could be. But basically how can one shoot a nail through a hard round pebble?