Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

WIP: a completed door

Posts

WIP: a completed door

#1

WIP: a completed door

Derek Cohen (in Perth, Australia)

Well, it may just work out ...

Both doors are essentially done, but I have only glued up this one. I wanted to check it for strength before I wasted time on the second.

What a tough job this was to glue up! Glueing up a rectangluar frame-and-panel is child's play compared to the balancing act I went through as a result of the curved frame. Finally it was done, and secured with tape (I could not use clamps), and I took it indoors to help the glue dry (it is Winter in Perth, and quite cold).

Here is the finished door with a coat of oil.


The panel is Karri and the frame is Jarrah.

Dimensions: The door height is 23". The total height of the cabinet, including the top and legs, will be 27".

There were a few "marks" on the panel - not figure, rather it was as if the wood was stained. This would not scrape off. I managed to align it with some figure in the frame, which I thought did a good job of distracting the attention away from it ...


I really wish I could produce a set of drawings to explain what I am trying to create. The best I can do to give you an idea of the way the door will look in the unit (although I should say units since there is a second, mirror-imaged one being built at the same time) is model it this way ...

Imagine that the door, which is 13" wide, is at the end of the cabinet. The cabinet will extend 6" further back (to the left). Alongside the door to the right there will be a bank of drawers 24" wide.


My apologies for the poor lighting. The flash on the camera is all I had, and it is not great. Better pictures later.

Regards from Perth

Derek

Re: WIP: a completed door

#2

Character mark

Bill Houghton, Sebastopol, CA

Looking very good. I think those grain marks add some character to the door, and placing the panel's mark next to the frame's mark was a good move.

My grandparents had some older factory furniture, with several grain peculiarities, and I used to admire them every time we visited; so I don't think you should see the mark negatively. It demonstrates that this is real wood, not plastic.

Re: WIP: a completed door

#3

Re: Character mark

Derek Cohen (in Perth, Australia)

Thanks Bill.

Actually I love those blemishes. That's the character of wood. However if the mark had been on its own it would look out-of-place. Alongside the figure in the frame it just blends in.

Regards from Perth

Derek

Re: WIP: a completed door

#4

Or Beauty mark...

Scott Burr in Ben Lomond CA

I like how it turned out. Did you go with your original rail and stile design Derek?

Re: WIP: a completed door

#5

Re: Or Beauty mark...

Derek Cohen (in Perth, Australia)

Hi Scott

Thanks.

Yes, it is the original design. As I mentioned to Pam in an earlier post, I liked the idea of hiding end grain with a mitred join, but when it came to looking at the effect up close, a mitre was out-of-place with the overall design of the cabinet.

Once the other door is glued up and both meet a "stress test" (no movement when I hold up the doors from the underside of the frame), then I will move on to the carcases. If the door frames do not pass this test, I will use the panels and build the doors without a frame ... and frame the panel with a face frame instead .

Hopefully the next set of pictures will be the doors in the carcase with face frames ready for drawers.

Regards from Perth

Derek

Re: WIP: a completed door

#6

Re: WIP: a completed door

Larry Wyatt

The "beauty mark" and lining it up with another one is, to me, the real *art* of woodworking, Derek. I'm finally beginning to get the "what piece of wood goes with another for the best look" concept down. I applaud you for having done that in most every piece that you make. You, sir, are an artist.

Regards,

Larry