Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

How To Make A 14:1 Dovetail Marker

Posts

How To Make A 14:1 Dovetail Marker

#1

How To Make A 14:1 Dovetail Marker

Tom Colligan

In the November '09 issue of PWW, there was a two page article on making Dovetail Markers. The author recommended making a fence that would go in front of your mitre guage on the TS. For a 5:1, 6:1, 7:1 and 8:1 DT Marker, you need to make this fense 11.3, 9.5, 8.1 and 7.1 degrees, respectively.

But if you want to make a 14:1 DT Marker what would be the angle of this mitre guage slope? (I'm mathmatically challenged here so I appeal to this forum for some help.) TIA, Tom.

Re: How To Make A 14:1 Dovetail Marker

#2

Re: How To Make A 14:1 Dovetail Marker

Larry Barrett

The angle would (90* - inverse tan (14)) = (90-85.9) = 4.1 degrees.

Re: How To Make A 14:1 Dovetail Marker

#3

Re: How To Make A 14:1 Dovetail Marker

BrianA from Monument

Greetings,

The math here involves the use of the ArcTangent function.

1/14 = .071 ArcTangent is 4.086 degrees

Angle = ArcTangent ( Rise / Run )

Rise = 1

Run = 14

Brian

Re: How To Make A 14:1 Dovetail Marker

#4

Re: How To Make A 14:1 Dovetail Marker

Wiley Horne--So. Calif.

Hello Tom and all,

This is kind of a duhh comment, but just in case....I find it accurate and easy to take a sheet of ordinary graph paper and lay out three points--for the origin, the run, and the rise--and draw lines through these points.

Then transfer the marks onto the work. Lots of ways to do this, but I generally either (1) set a bevel gauge to the layout lines, or else (2) align the baseline of the drawing with a straight edge of the work, marking the origin on the work at the same time, and then stick a sharp point (compass point or scribe) through the 'rise' mark on the drawing into the work.

Wiley

Re: How To Make A 14:1 Dovetail Marker

#5

OK, I have to ask...

Denny

What are you planning on doing with 14:1 dovetails? Hardly a dovetail at that point, might look more like a mistake?

Just askin...

Re: How To Make A 14:1 Dovetail Marker

#6

I gave up doing math like this a long time ago...

Scott Burr in Ben Lomond CA

It's a very simple sketch in any CAD program and will yield the proper response.

Re: How To Make A 14:1 Dovetail Marker

#7

Maybe you want a 14* marker?

Chuck Nickerson

That's commonly used in casework. Its rise:run is 1:4.

Re: How To Make A 14:1 Dovetail Marker

#8

Re: OK, I have to ask...

Tom Colligan

Denny, this quote is from the Lee Valley site for their 14 degree DT marker: "The 14� marker is designed to approximate a 1:4 ratio, for those who prefer this angle when working in thinner stock, as it not only provides stronger material interlock than traditional ratio angles but produces a slightly exaggerated dovetail joint that many find attractive."

Re: How To Make A 14:1 Dovetail Marker

#9

Re: OK, I have to ask...

Derek Cohen (in Perth, Australia)

"The 14� marker is designed to approximate a 1:4 ratio, for those who prefer this angle when working in thinner stock, as it not only provides stronger material interlock than traditional ratio angles but produces a slightly exaggerated dovetail joint that many find attractive."

Hi Tom

A 14 degree marker is VERY different to a 14:1 marker. The ratio is calculated on a grid by marking 14 points (e.g. 14") vertically and 1 point (e.g. 1") at a right angle.

The angle so created is the angle of the dovetail.

Typical ratios are 8:1, 7:1, 6:1 and 5:1 These are chosen according to the thickness of the wood (lower ratios look better on thinner board because the dovetail ends up smaller), hardness of the wood (higher ratios are better the harder the wood), and just plane aesthetics (it really comes down what looks best to your eye as modern glues rule). A 4:1 (or 1:4 depending how spatially challenged one is) will create a very wide dovetail.

Here are examples of rations from 5-, 6-, 7-, and 8:1


A tutorial here for the above: http://www.inthewoodshop.com/ShopMadeTools/Dovetailmarkersinbrass.html

For most drawer sides, roughly about 3/8" thick boards, I tend towards a 7:1 ratio. My favourite (shopmade) dovetail marker (its a joke .. dovetailed dovetail marker :)) ...


Regards from Perth

Derek

Re: How To Make A 14:1 Dovetail Marker

#10

Jesper, Denmark

Re: The degree sign � is Alt 0176 

Jesper, Denmark

Re: How To Make A 14:1 Dovetail Marker

#11

craigd

Swapped 2 chars: � is Alt 167 

craigd

Re: How To Make A 14:1 Dovetail Marker

#12

craigd

Re: OK, I have to ask...

craigd

I suspect the OP meant 14� dovetails, nice for thin work. For example, these 14� ones are on 3/16" sides:


img

Re: How To Make A 14:1 Dovetail Marker

#13

I use Alt+248 �    14�

Tony - Memphis