Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

A CPM3V Chisel

Posts

A CPM3V Chisel

#1

A CPM3V Chisel

Dominic in Buck's County PA

Hi Gang,

I was lucky enough to get one of John ("jcav8ter" on WoodNet) Payne's prototype CPM 3V chisels to try out. This one is a 1/2" bevel edge chisel. Normally they come "fully assembled", but John knows I love to tinker and sent me the raw materials to build my own.

I turned the new coccobolo handle last night. The ferrule was fitted to the tenon and then epoxied in place with Loctite's 5 Minute 2 part Epoxy. I used a LN handle as a template then made it a bit longer so it will work better as a parring chisel.

CPM 3V Chisel

After sanding I gave then handle several coats of sealer. Today I sanded it one more time and then gave it several coats of blond shellac buffed out with 0000 steel wool.

I used 45 micron diamond paste to flatten the back. It went a lot faster than I had expected. I thought I'd be at it all night. But it took only a bit longer than a "standard" chisel did. After flattening I polished the back to a mirror finish.

CPM 3V Chisel

The blade got hollow ground on my grinder and then sharpened using 220 grit sandpaper (to establish the bevel) and the 1000, 5000, & 8000 Japanese Super stones. I then honed with Veritas Green Honing compound on MDF. It is DAMN sharp.

CPM 3V Chisel

Here it is next to a similarly sized LN chisel. Like I mentioned above, I made it longer to help me use this as a parring chisel.

CPM 3V Chisel

BTW, the blade was epoxied it in place using the same stuff I used on the ferrule. After it set, I was able to parr end grain pine with no problems.

CPM 3V Chisel

Overall I'm pretty happy with the outcome. If any of you are hesitant about getting these chisels because you think they'll be hard to sharpen, don't worry. I could handle them pretty easily. You just have to expect it'll take a bit longer to get the edge going. After all, it IS harder steel.

Anyway, I look forward to actually using it on a project and will report back as soon as I have more data on it's edge retention.

See ya around,

Dominic

Re: A CPM3V Chisel

#2

Nice...

Scott Burr in Ben Lomond CA

Work on the handle Dom! Look real nice. Hope I can do that one day.

What did you use to seal the coco?

Please let us know how it works out for you.

Re: A CPM3V Chisel

#3

Re: Nice...

Dominic in Buck's County PA

Thanks Scott. I used Bulls Eye Shellac Sealer (which is just dewaxed shellac).

I used that same finish on my bow saw's cocobolo handles and they've held up to about a year's worth of handling.

Re: A CPM3V Chisel

#4

Dom, A CPM3V Chisel

Tom Colligan

Thanks for the post, Dom. Is there anyone selling these chisels in rough blanks. I too would like to finish the chisels myself but have put off buying the stock in bars, assuming I could find any sellers of this product. Thanks for your reply.

Re: A CPM3V Chisel

#5

Re: Dom, A CPM3V Chisel

Dominic in Buck's County PA

Thanks!

I'm sorry, I know of no one selling the rough blanks.

Re: A CPM3V Chisel

#6

Re: Dom, A CPM3V Chisel

Derek Cohen (in Perth, Australia)

Not chisel blanks, per se, but you cabn get the steel from Crucible Specialty Metals. From what I have gathered, it is easy to work in pre-tempered format. Saw, grind, then send off for heat treating.

Regards from Perth

Derek