Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

A refurbed Bedrock Type 5 606C

Posts

A refurbed Bedrock Type 5 606C

#1

A refurbed Bedrock Type 5 606C

Dominic in Buck's County PA

Hi gang,

A week or so ago I picked up the sole and frog for a Bedrock Tye 5 606C off of Ebay. I got it for a pretty good price (at least I THINK I did). But as you know, I'm a sucker for Bedrocks. Especially ones that need a bit of TLC.

This baby arrived and after looking at it I was convinced that I could make a go out of it. The body was rusted to the point where the japaning was gone. But the sole and sides were really not that. The frog was in somewhat decent shape and the hardware needed a severe cleaning.

Bedrock Type 5 606C BEFORE

Bedrock Type 5 606C BEFORE

Bedrock Type 5 606C BEFORE

I ended up soaking the frog and body in Evaporust not once, but TWICE. Let me tell you something, when Evaporust goes BLACK, that means it DEAD After dunking it got cleaned with a brass wire wheel.

Cleaning the sole amounted to stripping off the rest of the Japaning and then prepping it for spray painting. I masked all the mating surfaces with blue painter's tape and went to work. I used Rustoleum primer (the kind that converts rust to a paint able surface) and then over the next couple nights I gave it 6 coats of Hammertone black satin enamel.

After the paint was dry I addressed the sides, sole and the rest of the plane. The sole was corrugated. So that made flattening a breeze. The sole and sides are not pristine by any stretch of the imagination. The sides have areas of small pitting as does the sole. I had some concern early on that the area in front of the mouth would be damaged. But it turned out to be more like a discoloration rather than pitting. And none of these intersect the leading edge. So it is not a worry (as you can see from the shavings in the photos below). After lapping, I gave all areas a nice buffing up to 600 grit.

I had a very nice old rosewood tote and knob that I just refinished waiting for this bad boy. They were given several coast of blond shellac rubbed out with 0000 steel wool. I must say that now I know why craftsmen preferred rosewood. That stuff finishes beautifully!

I had a Bedrock Lever cap that had a chipped edge. I carefully ground that down smooth, sanded it and polished it until it looked perfect. Next to an identical one you can hardly tell the difference. And what's more, it works just fine.

The tote and know hardware as well as the iron and chip breaker came from that crappy old 4 1/2 I parted out. I have no idea what that plane iron was made from but it took me nearly 1/2 hour to use diamond paste and a steel flattening plat to lap the back flat! After that I sharpened with Japanese Super Stones and honed with LV Green Honing compound. I'm not saying that I got the edge super sharp or nothing. But I was afraid to put it too close to anything because it might come in contact and cause a fission reaction (you know,...because it was SO sharp that it would split an atom,......eh,.....ah,...........................................No one gets me)

Well, here it is. It isn't going to win any beauty prizes, but I like the way it performs. And that's all that counts.

Bedrock 606C Type 5 AFTER

Bedrock 606C Type 5 AFTER

Bedrock 606C Type 5 AFTER

Bedrock 606C Type 5 AFTER

And here it is working on some walnut, alongside it's smooth soled "brother".

Bedrock 606C Type 5 AFTER

As you can see, it can pull a nice shaving. And it leaves a surface as nice as my other 606. I plan on cambering the blade a bit more and using this as a "surfacing" plane.

Thanks for viewing

See ya around,

Dominic

Re: A refurbed Bedrock Type 5 606C

#2

NICE work, Dominic!!!  VERY nice!!

Larry Wyatt

Re: A refurbed Bedrock Type 5 606C

#3

Dude...

Scott Burr in Ben Lomond CA

PAINT!?! >(

Do's I needs to's come overthere's and kick your's A##!

Dom, damn next time tell me and I'll ship you some japanning!

Also...

And it leaves a surface as nice as my other 606


YOU SUCK TOO, BIG TIME :D :D :D :D

Otherwise a nice job on the "latest" 606 :b

Re: A refurbed Bedrock Type 5 606C

#4

WOW!  I wonder how many people

Wiley Horne--So. Calif.

walked by that hulk of a plane and never gave one thought to what it could be! Superb work!

Your idea of using it like a true fore plane (what a concept) is excellent IME. Foreplane is all you need for roughing--it flattens in the bargain.

Am glad all your hard work was so well rewarded!

Wiley

Re: A refurbed Bedrock Type 5 606C

#5

Re: A refurbed Bedrock Type 5 606C

Philip Duffy

Dom, You have done it again!! Congratulations on another fine result. Phil

ps where do I find a bolt for the front of the tote on a NR5?

Re: A refurbed Bedrock Type 5 606C

#6

Re: A refurbed Bedrock Type 5 606C

wilbur

I like your choice of the hammertone paint, even if it isn't the traditional method of finishing. It looks kind of cool, and it will give you a subtle but easy way of identifying which 606 you are looking at.

Nice job! And I have no idea what you mean about your latest project not winning any beauty awards. It looks plenty nice to me.

About your hard to flatten 4-1/2 blade: any way that it might be laminated? I've tried flattening the back of a laminated woodie blade before. It took a surprising amount of time and effort. That's why I like that Japanese plane blades have that hollow in it.

Re: A refurbed Bedrock Type 5 606C

#7

Re: A refurbed Bedrock Type 5 606C

Dominic in Buck's County PA

Wilbur,

Thanks for the compliments!

I think you "hit the nail on the head" my friend! I believe it IS a laminated iron. It's old enough and the proper vintage for this plane.

Re: A refurbed Bedrock Type 5 606C

#8

Re: Dude...

Dominic in Buck's County PA

Yeah, I know, I know! But japaning was out since the only kind I knew of required baking time. I don't want to think about what it would take for me to use my oven to bake a plane! My wife already has enough reasons to be mad at me! :D

I usually avoid planes that need this level of clean up. And if a plane needs new japaning, I will most likely stay away from it. But Bedrocks in particular are my weak spot. To be truthful I was conflicted over using the paint right up until the point where it dried. It was then that I realized it actually looks pretty good.

You wrote:

"Also...

And it leaves a surface as nice as my other 606

YOU SUCK TOO, BIG TIME"

I guess you forgot about that K6C I just cleaned up as well, eh? :D :D

I'm telling you, I have a problem!

Re: A refurbed Bedrock Type 5 606C

#9

Re: A refurbed Bedrock Type 5 606C

Dominic in Buck's County PA

Thanks Phil!

You wrote:

"where do I find a bolt for the front of the tote on a NR5?"

I believe that's the same size as the bolt for the frog adjuster clip. But I would check with my favorite source for old plane parts, Walt Quadrato at Brass City Records and Tools (203 574-7805).

Re: A refurbed Bedrock Type 5 606C

#10

Re: WOW!  I wonder how many people

Dominic in Buck's County PA

Thanks Wiley.

Re: A refurbed Bedrock Type 5 606C

#11

You make that look SO easy, Dom!

Bruce, a MN Galoot

Very nice job!

Re: A refurbed Bedrock Type 5 606C

#12

Thanks Bruce!

Dominic in Buck's County PA

Re: A refurbed Bedrock Type 5 606C

#13

Length of fore planes

wilbur

I hope this won't wander too far off topic, but it's interesting to me that the conventional wisdom for Stanley type planes is to use a #5 for initial roughing which is 14" long, but for wooden planes you use a fore plane that is 4" longer. Why is that? As Wiley says, the extra length on a true fore plane or a #6 (or 606, in Dominic's case) allows you to flatten the board than a #5 will.

Re: A refurbed Bedrock Type 5 606C

#14

scott grandstaff

Baking Paint

scott grandstaff

Nice job Dominic. It'll be a favorite I'm sure.

As far as japanning and paint, you can bake paint same as you do japanning.

In fact, if you want paint really thick and really hard, you have to.

Do a couple coats and air dry. Set your oven on lowest temp. Bake for 1/2 an hour.

Do a couple more coats, ditto. Bake again.

When you get it thick enough, bake for lowest temp, let cool.

Increase the heat 50 degrees, bake again, cool.

Third time is the charm. Bump it up another 50-75 degrees.

When it cools from the third baking, it will be almost as hard as glass.

If you don't bake the paint, and especially inbetween coats, it will never be anywhere near as hard.

But baking paint smells no better than baking japanning. Probably worse.

So if your mate is not a double feature movie buff, or addicted to long mall shopping trips or something, ahem...... (maybe a bridge or pinochle club??)

Better hit the salvation army/yard sale for a cheap used stove and do it outside.

yours Scott