Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

So,I finally made my first handsaw handle

Posts

So,I finally made my first handsaw handle

#1

So,I finally made my first handsaw handle

Andy Lincoln,in Dearborn,MI

I had been watching/reading about Dom's latest work and it finally put me over the edge to put a handle on a been sitting,long forgotten Disston No.4.I made this one of walnut.It still need a few coats of shellac but I thought I get the jump on posting anyhow.


I found plenty of inspiration at Ray Gardiner's site Backsaw.net as well as from the Disstonian Institute.

I never had the original handle when I got the saw along with the miter box so I had no reference to go from,so I chose a handle that was aesthetically pleasing to me,not necessarily the proper or correct handle.


The saw nuts and medallion were scavenged off another saw (fairly new Disston with an ugly,uncomfortable handle.)

I was able to trace the handle outline from pictures on the aforementioned website.A big thanks to Ray Gardiner for including a grid with his pics .It made it much easier to get the size correct/close.

As a side note to that does anyone know if you can print a transparency with a laser printer?I am thinking that a clear view of the grain when selecting/laying out a blank would be helpful.

I may make another handle for this saw out of a different wood,maybe cherry with a different pattern and just see which one works,feels the best in use.Now I will have to get the Langdon Mitre Box out of the attic and re-mate it to the saw I received it with .Maybe I can send it off to Marv to be sharpened,wheat carved,and accented in John Deere green :)

Thanks for looking,

Andy

Re: So,I finally made my first handsaw handle

#2

Re: So,I finally made my first handsaw handle

Dan Donaldson

Nice handle.

Yes you can print transparencies on a laser. We did it at work all the time. Just go to an office store and buy the film. (As I recall, it is kind of expensive.)

Re: So,I finally made my first handsaw handle

#3

Various thoughts

Bill Houghton, Sebastopol, CA

Andy, you asked, "...does anyone know if you can print a transparency with a laser printer?" I know: yes. About any office supply store, local or online, should be able to sell you transparency paper. Before PowerPoint and computer projectors, we used this a lot at my employer for presentations: get the cool graphics and words set up on the computer, print them, and voila! You're ready for an overhead projector.

Nice looking handle. Don't go for the J.D. Green, the grain's too pretty. And, given your locale, I would think you'd want something besides wheat carving...tiny little roads with tiny little Fords on them?

You're going to love having a Langdon Acme box in your shop. I was amazed when I discovered that I could trim a sawkerf's width of wood from a piece of molding. No previous hand-powered miter box would permit that, as the saw would slide off the cut, but my Acme box holds the saw so firmly that it permits precise cuts.

Re: So,I finally made my first handsaw handle

#4

Re: So,I finally made my first handsaw handle

steve mackay

Pretty cool. I guess I like the walnut as much as the apple wood.

Re: So,I finally made my first handsaw handle

#5

Very cool!!

Dominic in Buck's County PA

Andy,

The handle looks GREAT! And I think it totally fits.

You wrote:

"As a side note to that does anyone know if you can print a transparency with a laser printer?I am thinking that a clear view of the grain when selecting/laying out a blank would be helpful."

As mentioned in another response, you can get transparency film for a laser printer at any office supply store. However, I just printed a couple extra copies and cut one out exactly to size. I found that just as helpful when laying out the handle for grain orientation. Another thought is to just get some tracing paper and put a sheet of THAT in your laser jet. That ought to work just as well.

"I may make another handle for this saw out of a different wood,maybe cherry with a different pattern and just see which one works,feels the best in use.Now I will have to get the Langdon Mitre Box out of the attic and re-mate it to the saw I received it with......"

You have a Langdon miter box all ready for this one? Now I'm jealous! :D I need to find one to go with that 16"' Disston Miter saw I just restored.

Later,

Dominic

Re: So,I finally made my first handsaw handle

#7

Re: So,I finally made my first handsaw handle

Marv

Good job, Andy,

Looks like you didn't waste any blade space with the set-back cheeks. Looks good that way and probably gives it a nice hang.

Would be glad to sharpen and wheat carve your saw, but lets give some thought about that John Deere green. :)

A nice Ebony black might look good though.

Marv