Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Crown Gents dovetail saw handle conversion

Posts

Crown Gents dovetail saw handle conversion

#1

Crown Gents dovetail saw handle conversion

Dominic in Buck's County PA

OK, so I have this Crown Gents Dovetail saw and I've been wanting to make a new handle for it for the longest time.

Photobucket

The handle just popped off with minimal force. Here is a photo with the template of the Graymercy Dovetail saw handle

I then cut the "tang" off of the saw plate and then used a dremel and abrasive cut off disk to cut an angle at the back of the saw plate. This angle matches the one on the Graymercy template. Notice the spine is angled as well? That'll be cut straight later on.

Photobucket

I chose some very cool looking lacewood for the handle. It's a bit light but the weight compliments this small dovetail saw nicely. After surfacing the blank to just a bit over 7/8" I attached the template with some 3M spray adhesive, and drilled out the curves, then bandsawed the shape out.

Photobucket

I then drilled the holes in the handle for the saw nuts using the locations on the template. These holes will help me to locate the holes in the saw plate.

Photobucket

I then cut the kerf using the same technique as I used during my Disston Keystone Dovetail saw project. Once the kerf was cut the mortise for the spine was let into the handle.

Photobucket

After that I used a transfer punch to locate the holes in the saw plate

Photobucket

Photobucket

Then the handle was shaped, scraped, sanded, and given several coats of blonde shellac.

Photobucket

And here's the completed saw:

Photobucket

Photobucket

It feels very balanced in my hand. And I like the shortness of the plate. It'll be perfect for smaller projects. I need to wait until I get my Somax saw set from TFWW. Then I'll sharpen it up. Right now it doesn't cut well at all

Photobucket

And here it is in it's new home (until I make a hanger for them on my inner cabinet door)

Thanks for viewing.

See ya around,

Dominic

Re: Crown Gents dovetail saw handle conversion

#2

NICE! VERY, VERY, NICE!

ROBERT HAINES

Re: Crown Gents dovetail saw handle conversion

#3

That wasn't exactly a sow's ear to start

Bruce, a MN Galoot

but you sure made a silk purse out of it. Really nice job, Dom! I have a similar thing in mind for a Disston backsaw I don't like.

Re: Crown Gents dovetail saw handle conversion

#4

Very cool, Dom. Nice job!   

Hank Knight

>:)

Re: Crown Gents dovetail saw handle conversion

#5

Re: Crown Gents dovetail saw handle conversion

Marv

Nice job on the handle Dom,

I'm probably the only person in the entire world who bought a Somax saw set from TFWW that broke off the teeth of a dovetail saw I had sharpened. TFWW advertises two different saw sets, however, as far as I know they only have one size. (the blue one) When you get the saw set, there's a message printed on the side of the box explaining that the maker of the saw set has made it so it will set all sizes of teeth. When I adjusted the anvil for the smallest tooth, it either broke the tooth off, or it put too much set in the tooth. After some research, I discovered that the angle they use on the anvil is about 23 degrees compared to only 15 degrees on the popular Stanley 42X saw set that everyone is buying on eBay. The Stanley 42X allows you to adjust it so it will put minimum set in the teeth, like only .003 or .004 set each side of the blade. This is all you need for a Dovetail saw.

I might add, Joel willingly offered to refund my money including all shipping. I chose to keep the tool with intentions of making it work because there are other features that I like. I'm waiting for a blade I can experiment on without worrying about breaking teeth.

For the smaller teeth, such as 13PPI and smaller, grind or file the front edges of the hammer on the 42X at an angle, leaving a small flat on the front end. I have two 42X,s. One I have modified and the other I didn't. I will never use any other saw set but a Stanley 42X.

Marv

Re: Crown Gents dovetail saw handle conversion

#6

VERY cool !

steve mackay

Re: Crown Gents dovetail saw handle conversion

#7

Re: Crown Gents dovetail saw handle conversion

Ralph Johnson

Marv

What is the differance between a stanley 42 and stanley 42x saw set. Also from what you are saying if i want to buy one i would want a 42x, is this right.

thanks Ralph

Re: Crown Gents dovetail saw handle conversion

#8

Re: Crown Gents dovetail saw handle conversion

Marv

Ralph,

Big difference between the various Stanley saw sets and the different model numbers. Too many sellers are not aware of the differences and don't describe their tool for the unaware.

The model number, 42X for example is stamped on the inside of the handle and also on the top of the main casting. Often times the X isn't well stamped or cast into the casting.

The 42X has an anvil that is adjustable up and down with a knurled screw that fits into a slot in one side of the anvil that moves it when another knurled screw is loosened at the front. There are hatch marks on one side of the anvil that acts as reference so you can learn which adjustment is right for your particular saw. Once you get it right, you usually just leave it set that way, unless you use your saw set for both large and small teeth. It's handy to have two saw sets for this reason.

If you buy on eBay, make sure the seller is including a picture of the model number. Once you know what the business end of the tool looks like, you won't need a model number to know the difference.

Marv

This is what a 42X looks like.





Re: Crown Gents dovetail saw handle conversion

#9

I have a Pax saw waiting for the same project

Bill Houghton, Sebastopol, CA

but it's so deep on the list that the Internet will probably be replaced by whatever technology's next before I do it.

Re: Crown Gents dovetail saw handle conversion

#10

Saw sets

Bill Houghton, Sebastopol, CA

Disclaimer: observations and questions here from someone who has yet to sharpen a saw.

My Stanley 42 and 42W have the same adjustable anvil. What the 42X seems to offer is a two-piece plunger, with an outer part that comes forward first to engage the sawblade below the tooth line, sandwiching the saw between two pieces of metal, before the inner part comes forward to set the tooth.

I'm curious, Marv: some years back, one of the saw gurus du jour (Harold Payson?) recommended the Taintor* saw set, which has the same feature. Have you ever tried one of those, and, if so, what about the Stanley 42X makes it more attractive to you?

As part of my shed cleanup, I realized that I've got somewhere north of a dozen saw sets. Kind of silly (but they're so cheap at garage sales!).

*A name that always makes me look over my shoulder for Tarzan.

Re: Crown Gents dovetail saw handle conversion

#11

Re: Saw sets

Marv

Bill,

The 42W has an adjustable anvil, but it is much like the Somax in that it rotates, where as the 42X slides up and down. It's ok, but the saw set doesn't have the clamping plunger you mention that the 42X has. The 42W tends to slip upward on the tooth as it is trying to bend it. The 42X stays in place. It's the clamping plunger that makes it superior in my opinion. The Somax has the same feature, but the anvil has more of an angle that produces too much set, even on it's lowest setting. Some people don't seem to mind too much set. Maybe it's just me. I prefer a smooth cutting saw. Too much set gives you a rough cut.

The Tainter No.7 is a good saw set, however I don't like the shape of the hammer as much as I like the 42X. The Tainter's hammer is kind of undefined and is a little more difficult to center on the smaller teeth. I have one and do use it when I need to set teeth that are too close to the handle for the 42X. The plier handles are at a different angle to the saw when in use compared to the 42X. Same thing with the Somax. Normally I remove the handle, but sometimes it isn't practical to do so. The Tainter is a little mechanical marvel formed from flat steel parts. I guess I like it because of that more than how well it sets teeth. The anvil is a bit wierd. The flats are numbered but do not relate to PPI. So it can be a guessing game to learn which flat to use for a particular size tooth and how much set you will get. Takes some experimenting. For setting smaller teeth, it comes with a flat washer that needs to be under the anvil. Not much guessing when using the 42X

Marv

Re: Crown Gents dovetail saw handle conversion

#12

Another fine job Dom!

Scott Burr in Ben Lomond CA

What a difference! I have a Disston straight handled saw I don't use much because I don't like it's handle. I might have to borrow your design ;)

Re: Crown Gents dovetail saw handle conversion

#13

Re: Another fine job Dom!

Dominic in Buck's County PA

Scott,

Thanks buddy.

You can download the directions along with the template from the TFWW Website

9� Dovetail Saw Kit Instructions

The directions pretty much tell you what to do and WHEN to do it. Well worth the download.

See ya around,

Dominic

Re: Crown Gents dovetail saw handle conversion

#17

Re: Another fine job Dom!Slight Hijack

Andy Lincoln,in Dearborn,MI

Dom,

Do you happen to have a CAD drawing or tracing of the handle you refurb'd for the

Disston Mitre Saw?Mine is sitting without a handle as I do not have a guide to start from.I was thinking of trying to trace a photo of a Disston No.9 handle from a web photo but I really don't know if the scale is right for a larger saw.

Thanks,

Andy

Re: Crown Gents dovetail saw handle conversion

#18

Dominic in Bucks County PA

Re: Another fine job Dom!Slight Hijack

Dominic in Bucks County PA

Thanks Andy. I don't have a CAD drawing of the handle for the Disston Miter Saw since it's existing handle was in such great shape. However, I do believe that Ray Gardiner's site, www.bacsaw.net has photos of all sorts of back saw handle overlayed with 1"x1" grid. That way you can print them out and check dimensions and proportions.

Re: Crown Gents dovetail saw handle conversion

#20

Re: Another fine job Dom!Slight Hijack

Andy Lincoln,in Dearborn,MI

Thanks Dom & Scott,

That was the website I had seen but forgotten.I will peruse it carefully and see what it leads to.

Andy