The Saga of the Pruner Handle "Project"
John Aniano in Central NJ
Hello All,
About 10 years ago my wife Debbie and I bought a Japanese-toothed pruning saw for working in the garden. It got a lot of use, and finally the blade became dull. With it's impulse-hardened teeth, I could not file it, so I recently bought three replacement blades on eBay. One blade fit the old handle perfectly and we were back in pruning business.
Then I thought "I have 2 more sharp blades, why don't I make a new handle for one of them and we will have a pair of pruning saws". That was my first mistake.

Copying the original beech handle looked to be an easy project. It consisted of two holes for a pair of saw nuts I had been saving for just such a project, a simple curved profile, a bit of rounding, and I had a large 10 foot long plank of 1" thick quartersawn beech I had bought for making saw handles. I then said to myself "That beech plank is huge - it will take a lot of effort to get it into my shop and hand saw a section off to make this little pruning saw handle". Then I noticed the small, narrow strips of bloodwood my friend Stephen Thomas had given to me a few years ago. "Perfect size!" I said, and carried one of the bloodwood pieces into the shop and traced out the handle profile. By this time, I had unknowingly made several more mistakes in judgment...

I drilled out the holes for the saw nuts using forstner and brad-point drills on my drill press. Easy task! Part of the profile matched a ~1-1/4" forstner bit, so I drilled fully through to make this portion of the profile. Not so easy! - the forstner bit protested! Then, with my bandsaw, I began to cut out the rest of the profile. That is when the burning smell began. I should have stopped at this point, but forged ahead while the acrid bloodwood burnt dust settled onto my shop's horizontal surfaces and formed a fog in the shop. I should have called it quits as I used the bandsaw to cut the slot for the blade, but kept on going. I had to open the shop windows to let in some clean air...
This project was to become my "INTHMHE" saw handle.
"I Need To Have My Head Examined" I said as I began to try to smooth off the profile with my antique wooden spokeshaves. One spokeshave after another failed to cut the dense bloodwood. The stuff was turning the edges of the antique cast steel blades! Finally I found one spokeshave that protested, but cut, albeit slowly. (The blade angle was ~30 degrees.) "What was I thinking" I said to myself. "This 'simple' wooden handle will take hours to make at this rate!" "Why couldn't I have used the beech?" INTHMHE!

With the protesting spokeshave, I cut broad bevels on either side of the profile and when the bevels were done, I used the shave to round off the edges. In the concave regions of the handle, half-round files and a bow making knife made of HSS came to the rescue. The files clogged as though I was filing aluminum! My German hand-cut rasps fared a bit better, but were only good on the convex regions. INTHMHE!

Some really tough 3M sandpaper worked great to smooth off the rounded portions of the profile. The flat sides of the handle were smoothed with a minimum of tearout with a smooth plane.
Time was spent getting the saw screws and nuts to fit into the aluminum-like bloodwood. A narrow chisel and gouge got this task done. I test fitted the screws and made sure the blade could be held secure with the nuts.
Being the perfectionist that I am, the whole shaping and blade-fitting processes took maybe 2+ hours over three evening sojourns to my shop. INTHMHE...
Finally, I immersed the handle in a jar of linseed oil and turpentine I have for just such occasions. It remained there for 5 days. Often there is a foam of bubbles on the top of the oil when I immerse handles made of normal woods, but with this alumnio-bloodwood handle, no bubbles were observed...



After fitting the blade for the last time and a coat of a wax/linseed oil mixture this "simple project" was done.
Dense. Hard. Bloodwood. My brain. "Why couldn't I have used the beech?"
INTHMHE...




