Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

A restored Keen Kutter K6C

Posts

A restored Keen Kutter K6C

#1

A restored Keen Kutter K6C

Dominic in Buck's County PA

Hi gang,

Some recent questions about cleaning planes got me thinking that it was about time I took care of a Keen Kutter K6C I got off of Ebay about 8 months ago. I've been keeping my eyes out for Keen Kutters for a while after I learned they were just early type Bedrock in disguise.

I chose to use Evaporust this time for rust removal so I went to Harbor Freight (armed with a 20% off coupon) and picked up (2) 128 fluid oz bottles for $17.99 each (less 20%).

Here 's some photos of the plane before I started the cleaning process.

Keen Kutter K6 Before

Keen Kutter K6 Before

Keen Kutter K6 Before

After disassembly, I planes the parts in my new High Tech Evaporust "dunk tank". It's really just a 30" long section of 4" light wall PVC sewer pipe with a pipe cap glued onto one end.

Evaporust

Just a note here for those interested or curious. Once a No 6 sized plane is dropped in, one 128 Fluid Oz bottle of Evaporust will fill a 4" dia pipe up to about 27". So, in theory one bottle will be enough to totally submerge and clean a No8 plane.

After letting the parts sit over night I drained the Evaporust back into it's container. I used a paint strainer in a funnel to catch any stray bits of gunk before they got back into the bottle. As mentioned previously, the parts come out slimy. And the finish is kind of gray on all the ground/machined surfaces.

Parts right after Evaporust

But after wiping them down with mineral spirits and a very light touch up with a brass wire wheel brush (installed in my lathe) I was able to get them to look like this:

Parts right after cleaning

This represents about 30 minutes worth of "easy" work with a brass wire wheel brush. And THAT'S why I use Evaporust. After flattening the back of the iron, I reground the bevel, cleaned and polished the chip breaker, and then turned my attention to the rosewood tote and knob. These were really in fantastic shape and needed only to have some white paint removed. A quick wipe with lacquer thinner followed by several coats of sealer, then several coats of blonde shellac, then buffing out with 0000 steel wool and wax left them looking clean. But not overly shiney.

And now the reveal:

Keen Kutter K6 After

Keen Kutter K6 After

As you can see this plane is in excellent shape. The japaning is almost 99% and the iron looks like it only got ground once or twice. It's nearly full length. And once sharpened it was able to take a full width shaving with little effort.

Keen Kutter K6 After

Thanks for viewing!

See ya around,

Dominic

Re: A restored Keen Kutter K6C

#2

Re: A restored Keen Kutter K6C

Ron in Sterling, CT

Hi Dom,

Beautiful job. It looks like it just came out of the store. I have a Bailey No. #3 that I picked up at a flea market for $3 that will be my first rehab using Evaporust. Seeing your results makes me want to get at it.

Ron

Re: A restored Keen Kutter K6C

#3

Jim DeLaney, Austintown, Ohio

Re: A restored Keen Kutter K6C

Jim DeLaney, Austintown, Ohio

Nice, Dom!

Those 'single K' Keen Kutters are among my favorite planes.

Maybe it's just me, but it also seems that the wood on them is usually nicer than on comparable Stanleys.

Jim D.

Re: A restored Keen Kutter K6C

#4

No matter the flavor . . .

steve mackay

. . . I got that "C" Jones ! Actually, I didn't know they "did" "C". Intell-esting !

Re: A restored Keen Kutter K6C

#5

Re: A restored Keen Kutter K6C

Dominic in Buck's County PA

thanks guys!

Re: A restored Keen Kutter K6C

#6

Re: A restored Keen Kutter K6C

Bruce, a MN Galoot

That is a fine job, and a fine find, Dom! Do you need a new next door neighbor?

Re: A restored Keen Kutter K6C

#7

Well done Dom.

Scott Burr in Ben Lomond CA

How does the quality of the KK compare to a Stanley?

How about the tote shape and feel?

Another fine rescue indeed!

Re: A restored Keen Kutter K6C

#8

Dominic in Bucks County PA

Re: Well done Dom.

Dominic in Bucks County PA

When I said they were Bedrocks in disguise, I wasn't kidding! This K6C is pretty much identical to a Bedrock type 3-4 (round sided) 606C. So basically, they ARE Stanley hand planes. Just made to be sold by someone else. In this case I believe it was Simmons Hardware(?). So the quality is pretty high up there. The tote and knob feel just like those on my 606.

Re: A restored Keen Kutter K6C

#9

Re: A restored Keen Kutter K6C

wilbur

That's a gorgeous restoration job you did on this plane, Dom!

Of course, by now that's pretty much what I expect from you. ;)

Re: A restored Keen Kutter K6C

#10

Re: A restored Keen Kutter K6C

Bob Entwisle in NJ

Nice Job, Dom!

After seeing this and one or two of your other posts using Evaporust, I think it's time I pick up a gallon of that stuff.

I've fooled with electrolysis a bit, but it always seems like a grammar school science project gone awry by the time I get done.

Time to try something different!

Thanks

Bob in NJ

Re: A restored Keen Kutter K6C

#12

Re: A restored Keen Kutter K6C

Philip Duffy

WOW! Dom, you never cease to amaze me with your restorative talents. Thanks for showing all of us "how". Phil

Re: A restored Keen Kutter K6C

#13

Re: Thanks Dom...

Dominic in Buck's County PA

Scott,

Thanks buddy!

The plane iron is pretty much full length and sharpened up as well as any of the better old ones I have. The KeenKutter logo is sharp and clear as well.

Re: A restored Keen Kutter K6C

#14

Re: A restored Keen Kutter K6C

Dominic in Buck's County PA

Thanks Bob!

You know, electrolysis ain't so bad. Like any other tool it has it's uses. And it's a means to an end for a lot of people. If you already set up to use it, it's a snap to get going.

Evaporust's claim to fame is it's ease of use. I mean, can you get simpler than soak over night, clean with mineral spirits, then clean lightly with a wire brush?

Citric Acid also is nice. But I found (and this is just me) that I need to be near a sink when I'm using it. And that you have to keep an eye on the reaction so that it doesn't get too far along. But it's relatively cheap and it DOES work.

Re: A restored Keen Kutter K6C

#15

Thanks Wilbur!

Dominic in Buck's County PA

Re: A restored Keen Kutter K6C

#16

Thanks Phil

Dominic in Buck's County PA