Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Update on chair leg repair

Posts

Update on chair leg repair

#1

Update on chair leg repair

Derek Cohen (in Perth, Australia)

I thought that I would post this afresh as the original is a while back now.

As a reminder, we started with the good ..


.. and ended up with this ...


I decided to glue up everything using West Systems epoxy, recognising that the one side of the break - the side that had staggered leaves, should create a strong join - but the other side - the side with an in-line break - would require reinforcing ...


The leaves were glued together over three sessions. At the end the joins were pretty good - there will be tidying up later - and just one gap evident ...



Luckily, this gap was precisely where I planned the reinforcing would run. My plan was to mortice along the side and epoxy in a 1/4" wide x 1" deep Beech insert (the chair is Beech, just in case you were not aware :)). This would extend from the foot of the leg to about 4" above the break.

Because the mortice would be about 1/32" - 1/16" below the surface of the rear most lamination, I decided that this was a job for my power router, so close your eyes if this part offends.

Here is the set up ..

The router (my trusty Elu 177e that I have had about 20 years) is supported on runners clamped to the leg.


Here is the router bit over the hole ..


Ok, I will jump ahead - the mortice was squared up, the insert epoxied in, and the excess planed away after it was set. This is the result ..




and ..


I have now to use a cutting gauge on the insert to mimic the layers of lamination, and re-shellac (amber shellac) the finish. It is feeling strong.

More after the weekend.

Regards from Perth

Derek

Re: Update on chair leg repair

#2

Coming along

Bill Houghton, Sebastopol, CA

Re: Update on chair leg repair

#3

Re: Update on chair leg repair

Pam Niedermayer - Austin, TX

Now, see, that you even have a power router says more than you'd probably like. :) And here I was feeling guilty about my foot mortiser. Leg looks good, very good.

Pam

PS When you guys described your sons launching into a chair, I was incredulous; but then I noticed how my Baldric, easily 115 lbs, launches himself onto the bed for his self-described cute begging routine whenever I change clothes to go out. Only difference is our bed is a futon on the floor (my great grandmother's trick for maintaining mobility into her 90's).

Re: Update on chair leg repair

#4

Re: Update on chair leg repair

wilbur

Actually, I'm impressed that Derek's chair lasted through his son's teen years. Having seen the destructive power of my 7 and 3 year old boys, I'm planning on finding them alternative living arrangements when they hit their teens. ;)

Re: Update on chair leg repair

#5

Moses Yoder

How to raise children

Moses Yoder

To raise children, put them in a box and feed them through a hole. When they hit the teen years, plug the hole.

Re: Update on chair leg repair

#6

scott grandstaff

Love your Grandma!! OT

scott grandstaff

I sleep on the floor too.

I'd be paralyzed with a bad back otherwise.

Wore it out years ago.

When I got to a motel I don't care a bit about the bed.

Only thing I want to see,......... is how clean the carpet is!

yours Scott

Re: Update on chair leg repair

#7

Re: Love your Grandma!! OT

Pam Niedermayer - Austin, TX

Oh, yeah, count on it. I suspect that pallet on the floor was necessity to start. She and my great grandfather grew up during the civil war and he supposedly fought in it, but he was a child, so I doubt it. At any rate, it couldn't have been much fun living in Richmond at war's end. Sleeping on the floor combined with McKenzie exercises have saved my back.

Pam