Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

A bench with a difference

Posts

A bench with a difference

#1

A bench with a difference

Derek Cohen (in Perth, Australia)

I was given this bench about 12 or so years ago. Since then it has had the wood replaced and see a lot of use. Still, I wonder if anyone recognises it and can identify the manufacturer?

All I know it was built in Germany. My friend was to be the Perth agent, and when this did not take off, the bench lay in his garage for some years before he made a gift of it to me.


Essentially, the bench consists of two face vises within a steel frame that has a wood work top.

I have been using it to hold the chair I am repairing (which is when I thought to post it here)..


I added wheels, giving it mobility around the shop.


Here is another view of the double fase vises - I have a board clamped between. This make for a great dovetail vise, it is wonderful to hold long boards for routing mortices (since you can run a fence along the edge of the worktop), and it is sturdy enough to pound on with as much force as you can muster.


The end of the worktop also is an alternate home for my Zyliss vise (yes, it gets used!) ..


I would not swap it for two Workmates.

Anyone seen one before?

Regards from Perth

Derek

Re: A bench with a difference

#2

Re: A bench with a difference

John Pappas

Innovative. Offers many good ideas to anyone considering making a secondary bench. I have a Workmate and it makes a functional secondary bench. I can see why you like this more.

Re: A bench with a difference

#3

Re: A bench with a difference

ThomD

It looks like the fixed jaw is the front one? If so it is a workmate as far as the key difference in their original patent was concerned. Not that that helps you much I am afraid.

Re: A bench with a difference

#4

Re: A bench with a difference

Pam Niedermayer - Austin, TX

Don't know much about the make, etc., but it sure is intriguing. How do the vises work for dovetails? Seems like you have a lot of pretty far leaning to do to actually make the cut.

Pam, whose Zyliss also gets used, a lot

Re: A bench with a difference

#5

Dovetailing on the bench

Derek Cohen (in Perth, Australia)

Hi Pam

Using a board stretched between the two vises (which may be used individually, of course), the bench makes a terrific place hold boards for sawing dovetails.

I can understand that you imagined this to require one leaning across the bench, like this ...


... but, in fact, one works from the other side, like this ...


This example is really quite narrow, only about 3". However it is possible to work with much wider boards, up to about 30". The following mock-up is about 10" ...



Overall, this bench is the same height as my main bench. I use it as an extension and support when working wide/long boards.

Regards from Perth

Derek

Re: A bench with a difference

#6

Re: Dovetailing on the bench

Pam Niedermayer - Austin, TX

Actually, I understood that the only way to do it was from the other side; but that's a what, 6" board between you and the piece to be dovetailed? And you have to walk around it to reposition. Still a bit of a stretch; although perhaps not more than the average shoulder vise would require. I love the length/width it can accommodate. I even like the bench a lot, but would try to find something else for doing dovetails.

Pam

Re: A bench with a difference

#7

Re: Dovetailing on the bench

ThomD

Actually looks good for dovetails, shoulder vises, even with shortened screws are a lot deeper than that. Stand away is sorta the length of a forearm, so it ought not to be a problem.

Re: A bench with a difference

#8

Re: Dovetailing on the bench

Pam Niedermayer - Austin, TX

OK, but running around the bench time after time to set up for the next cuts doesn't satisfy my hobbyist need for speed. :)

Pam

Re: A bench with a difference

#9

Re: Dovetailing on the bench

Derek Cohen (in Perth, Australia)

Actually, Pam, you can simply lean over the bench to turn the vise screw handles- it is a fairly narrow. In any event, It takes 30 seconds to set up a board for sawing. Marking out and sawing is the main event, not clamping the board, and marking/sawing takes a bit longer. Long enough to want a comfortable, stable sawing position. This bench does offer that.

For contrast, the twin vises are used in the same way as I did some years ago when I had two face vises and spanned a board between them. Then, based on this, I built a simple face vise specifically for dovetailing (two-year old picture) ...



The only complaint I have with this is that it is a bit on the low side. The mobile bench ends up about 6" higher.

Regards from Perth

Derek

Re: A bench with a difference

#10

And that's why we have different bench designs. 

Pam Niedermayer - Austin, TX

Re: A bench with a difference

#11

Re: Dovetailing on the bench

ThomD

A yes speed. Maybe this would be a good time to try and sell a few more of Rob's Tucker vices... Oh right, I forgot, not made any more...

Re: A bench with a difference

#12

 

Pam Niedermayer - Austin, TX