Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Wood .. glorious wood

Posts

Wood .. glorious wood

#1

Wood .. glorious wood

Derek Cohen (in Perth, Australia)

I had an afternoon in the workshop today. Spent a little time epoxying the remainder of the chair leg (that I am repairing) back together. There's not a lot one can do after that except wait for it to cure. So I finally turned my attention to preparing the wood for a sideboard I have been planning for nearly 2 years.

The sideboard - if that is the correct term, for it is a combination entertainment centre and storage for crockery, glassware and drinks - will run along a wall in the living room and be a total of 4.6m long (a little over 15'). That's long which ever system you use to measure it. However it is only about 700mm (27 1/2") high.... I would be happy to hear recommendations for this height (to suit a flatscreen TV)The idea is to build it in 4 sections, with two smaller ends and two longer centre cabinets. The end cabinets will feature coopered doors. A rough plan will look like this ...


It's going to use a fair amount of Jarrah, our choice, partly because it is a dark wood which we want in this part of the room, and partly because I have been salvaging boards for some time. Much of it is ex-roofing beams, some from an alteration we did two years ago, and some from salvage yards. Jarrah is otherwise becoming a scarce and very expensive wood in Australia. It has been overlogged for generations, and much of it is now exported.

In preparation I even purchased an 8" jointer and a 12 1/2" lunchbox thicknesser - whose kidding whom here ... there is no way I am going to thickness all this very hard and heavy timber by hand. Been there and done that.

So here is some of what I completed this afternoon. Much of it is 2"x6", some 2"x8", and a few 2"x4". All rough sawn, of course, and "woolly". Collected more than my fair share of splinters today!



There is nothing more exciting that taking a woolly, grey board and cutting it open to reveal ...


... or, to take a woolly, grey board (did I say this before?) ...


... and it turns into this ...


At the end of the afternoon I had a heathly enough pile ...


So, where do you get your wood?

Regards from Perth

Derek

Re: Wood .. glorious wood

#2

Re: Wood .. glorious wood

Bill Houghton, Sebastopol, CA

Our salvaged wood in this house tends to be redwood - which is fine when it's the all-but-grainless old-growth stuff (I've had some pieces that hand-planed smooth as glass in either direction; it was even hard to tell which was end grain and which long). But it's not terribly good furniture wood, and, anyway, most of what we remove is badly done post-World War II fir framing, because the badly done finish details have tended to lead to rot. Rotted Douglas fir is interesting, briefly, but mostly as testaments to how well a wall can stand up even when the framing is all but gone.

All of which is to express much envy...I barely managed to avoid drooling on the keyboard, something (the drooling) my sweetie frowns on, since she uses it too.

Re: Wood .. glorious wood

#3

Where ? Dumpster mostly ! : O

steve mackay

Although I break down and shell out for dowel and oak.

Re: Wood .. glorious wood

#4

I'm Jelous...

Scott Burr in Ben Lomond CA

Very nice wood Derek. I'm in the same boat as Bill as far as salvaged wood goes. Mostly redwood around here, so I'm stuck going to the Hardwood stores around here for any other types.

I just finished up my G&G inspired "sideboard/ entertainment center. I'll post some pics soon. Mine is exactly 27.5" high. I have a 46" flat screen on it. It's at a great height for viewing.

Good Luck, That's one big project.

Re: Wood .. glorious wood

#5

Where?

Edward in Vancouver

Where do I get my wood?

It's kind of strange, I'll shell out for good tools, but I'm cheap when it comes to wood.

For instance....

My bench is made from the remains of two off-cast maple baker's tables, and from western (soft) maple salvaged from pallets.

Lots of red oak from pallets, yellow poplar, and maple are used to, ummm... "develop hand tool skills", and make shop equipment as well as gifts.

I also like the "day after" garage sales (for free, in the back lane) where I can get abused furniture and get some good wood from this as well. I once scored a 4' round TEAK table top this way. Of course it had a nasty split in it, and nails were used in the butt joints, but I digress. Many abused chairs have found a new life as tool handles and turned items. A lot of usable board feet in a tossed-out bed frame too....

I have bought 8/4 qswo specifically for my "gerstner style" toolchest (LV plans), and 4/4 and 8/4 birch and western maple for the built-ins and small items for my Cafe.

For some reason I feel like "George" on the old Seinfeld series when he was talking about parking: "Pay for parking?!!! Why, that's like going to a hooker, you don't pay for parking, you see what's available".......