Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Mouth Size on an Infill Panel?

Posts

Mouth Size on an Infill Panel?

#1

Mouth Size on an Infill Panel?

David Weaver

Good morning, folks. I have a panel infill kit (18") that I'm working on right now, and I think the only thing I have yet to decide is what the mouth on it will be. I'd kind of like to lean on the experience of folks who use one fairly often.

I generally prefer to have a mouth tighter rather than looser for a given task, and if I need a really open mouth for some unexpected thicknessing, I have other planes that can take care of that.

Only trouble with deciding is I have no panel planes to base a decision on, and I understand them to be something different than a fore plane (i hope, at least), and intended for slightly finer work.

What is a good mouth size on a new plane, exactly where you'd want to have it? A hundredth or two? Is this a personal preference thing where I may be well served by starting it off fairly tight - like a hundredth - and then opening it up as it seems fit from use?

Re: Mouth Size on an Infill Panel?

#2

Re: Mouth Size on an Infill Panel?

Derek Cohen (in Perth, Australia)

Hi David

Well a panel plane is a long smoother, so generally you want a tight mouth.

How tight? Tight enough to permit shavings to escape. Remember, you can always increase the size of the mouth fractionally, so make it too tight and work from there.

How important is a tight mouth? It does depend on (a) the type of wood you plan to plane (the more interlocked, the tighter the mouth .... unless ...), (b) the angle of the bed, in other words, the cutting angle - the higher the cutting angle, the less important the size of the mouth. At a cutting angle of 60 degrees (half pitch) the mouth size is relatively unimportant. At 50 - 55 degrees I'd say the mouth size is reasonably important, and around 45 degrees (common pitch) I'd say it is most important..

Clear as mud.

Regards from Perth

Derek

Re: Mouth Size on an Infill Panel?

#3

Moses Yoder

Re: Mouth Size on an Infill Panel?

Moses Yoder

My take on mouth size on planes for smoothing is that it should only be slightly larger than the thickness of the shaving. If you plan on using your infill panel plane for final smoothing the mouth opening should be about .003". If you use it like a jack plane before final smoothing you might be taking shavings that are a little thicker and should have a little wider mouth but probably not more than about .008".

Re: Mouth Size on an Infill Panel?

#4

Re: Mouth Size on an Infill Panel?

David Weaver

Clear, yes. It's a 45 degree plane, the kit comes with the wood and the bedding block is already set up at that. I'd have chosen 50 if I'd have made it from scratch.

It'll be the last time I make a kit - there are too many things I like to have control over that are already decided, but fortunately, the mouth looks to be just narrow of the iron passing through, so I'll be able to size it.

Sounds like really tight is a good place to start.

Re: Mouth Size on an Infill Panel?

#5

Re: Mouth Size on an Infill Panel?

David Weaver

Thanks, Moses. I just finished a 55 degree smoother with a mouth in the neighborhood of .004", and will be making a couple more of them at different pitches based on how it performs, so it won't need to smooth.

Based on your suggestion, and derek's maybe .005-6" to start and see where to go from there. I would like to be able to comfortably take .002 to .003 shavings with it.

Re: Mouth Size on an Infill Panel?

#6

craigd

Re: Mouth Size on an Infill Panel?

craigd

When I made my infill smoother (55� #4 sized), I made the mouth opening adjustable so I could play around and see what worked. I usually set it in the 0.006" - 0.009" range. It is currently set at 10 thou (0.01") and works nicely.

Craig