Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Miter saw question.

Posts

Miter saw question.

#1

Miter saw question.

Bruce, a MN Galoot

Last weekend, I found the first honest-to-goodness old tool in this old tool heck town, a Langdon Acme miter saw. It's in pretty decent condition, but today is the first that I've had time to take it for a test drive. Square cuts are dead on, but I noticed that the saw wasn't dropping all the way down to cut completely through. So I dragged the saw out and found that the teeth in that center cutting range are very dull. At the toe end, there are one or two teeth missing, and at the heel it's evident that this saw has been sharpened a fair amount. The blade is 3-3/8" deep at the toe and 3-7/8" at the heel, total length is 24-1/4".

So the question. What would be the normal rake and fleam angles for this critter? Are there any special sharpening conditions I need to watch for? If it's not too difficult I think I'll take a crack at this one myself. OTOH, if the advice goes the other way I'll send it out for an expert job. The teeth line up fairly well, that is, there is no noticeable crest or dip.

Thanks.

Bruce, ultra glad not to be on night shift for another month.

Re: Miter saw question.

#2

Re: Miter saw question.

Marv

Hi Bruce,

I'd just file it as a normal crosscut with about a 15 degree rake and and a 25 degree fleam. Give it just enough set so it won't drag in the kerf. This will give you a very smooth cut. Most of your cuts won't be very deep, so you don't need much set. We're talk'n only about .004 per side after a very slight side jointing.

Have fun,

Marv

Re: Miter saw question.

#3

while I have your attention, Marv,

Bruce, a MN Galoot

this is a fairly nice miter box, but nothing special to write home about. The handle is not embellished, so would it be heresy to add a little wheat carving to it? :D

Re: Miter saw question.

#4

Re: while I have your attention, Marv,

Marv

The first thing I'd do is wheat carve it. And then paint it John Deere green. (just the handle)

Marv

Re: Miter saw question.

#5

You're asking MARV?

Bill Houghton, Sebastopol, CA

Why does this reply not surprise me?

I think a carving of a northern pike would be better. No-see-ums, while also geographically correct, would be too hard to explain.

Re: Miter saw question.

#6

Northern pike

Wiley Horne--So. Calif.

Would someone who knows their way around northern pike 'splain a little about them. Several years ago, in my line of work (the water bidness), we had an agency manager here in So. Calif. who was from Minnesota--he could and would talk northern pike by the hour. Said they would grab squirrels off low-hanging branches over the water.

Even if you cut everything he said in half, they still sounded pretty ferocious. He clearly had lost his way coming here, and got back as soon as he could figure out how, but he left behind the legend of the northern pike.

What is the story on these fish?

Wiley

Re: Miter saw question.

#7

Re: Northern pike

Bruce, a MN Galoot

They are nasty, mean, cannibalistic, and can grow pretty large. The MN state record is 45 lbs. The have lots of small, very sharp teeth. Relatives of the muskie, maybe that explains their temperament. They also fight like the dickens. The smaller ones are pretty good eating, but here the walleye are considered the prime catch.

I don't fish, except once in a blue moon a buddy will take me out salmon fishing, mainly to laugh at me and my dumb mistakes. :D

Re: Miter saw question.

#9

Southern equivalent

Bob Hackett

Would be the Alligator Gar,a very aptly named,incredibly mean fish.They`re one of the few fish I didn`t feel sorry for when I saw bow fishers stalking them.The only thing good about them was that they ate Cottonmouths.

Pike are just one of the most aggressive and smart fresh water fish out there.I hooked one once while fishing from a dock that ran until it convinced itself that running wasn`t working.It promptly ran back,wrapped my line around a piling several times and snapped it like it had practiced the maneuver.A buddy who was with me thought it was a pike by the way it acted and proved it when he later hooked it himself and returned my lure after he landed it.He had a stronger pole and line and a cable leader.

Those who have never seen small furry creatures taken off limbs are just not coastal dwellers.Nothing beats salt water for re-arrangement of the food chain.Ask any Striped Bass or Blue Fish.

Every year someone loses at least one toy poodle or it`s equivalent off one of the tender floats in the Harbor.If the lobstermen are keeping their labs and retrievers safe and close in the boats then you would think the tourists would take the hint. :(

Re: Miter saw question.

#10

Re: Northern pike - yummy recipe!

wilbur

I'm not sure about the squirrel grabbing, but when I was growing up in Chicago, pike was a very popular fish for the Chinese restaurants to serve. Cook it by putting a whole cleaned pike, head, fins, and all, on a plate, cover it with a generous amount of cilantro and slivers of ginger and green onion, and steam the whole thing, about 8-10 minutes. You can test to see if it's done by inserting a toothpick -- it should go all the way through easily if the fish is completely cooked.

When done, pour off any liquid that might have collected in the plate during steaming, but don't worry if you don't get rid of all of it. Then add more cilantro and slivers of ginger and green onion, and heat up about 1/3 cup of peanut oil, and pour it over the fish. You should hear the freshly added cilantro, ginger and green onions crackle as the hot oil hits it. Then pour about 3 tablespoons of light soy sauce over it all, and serve with steamed white rice.

I love taking spoonfuls of the soy sauce/oil that collects at the bottom of the plate and putting it on the rice, and eating just that. Red snapper, sea bass, and flounder are also good fish to use for this recipe.

When I lived in Dallas, I made this for one of my friends from residency who loved to go fishing, and he figured out how to wrap a whole fish that he would catch in foil with ginger, green onion, and cilantro, and "steam" it in the foil while camping. He swore that it was his favorite way to cook fish, and up until he met me, he had never had fish cooked that way before. He grew up in Nebraska, where I guess the Chinese food selection is somewhat limited. Now he makes sure he packs some soy sauce when he goes fishing. :D

Re: Miter saw question.

#11

Yeah but....

Marv

I really enjoy the fish stories, but what about Bruce's mitersaw? :D

Re: Miter saw question.

#12

As always...

Bob Hackett

We defer to the master,and he has spoken.

After the boss spells things out for you there`s nothing left to do but either go to work or talk fishin`so... :)

Re: Miter saw question.

#13

You are a wonder,Wilbur.

Bob Hackett

We LOVE cilantro(and plant plenty) and I`ve been looking for ages for some way to beat my brother`s grilled tuna/swordfish.I can`t wait to spring this on him when he shows up this summer.

I owe you one buddy.

Re: Miter saw question.

#14

Question about Langdon miter saw

Wiley Horne--So. Calif.

Marv and all,

What was the original saw that came with the Langdon miter box? Was it a Disston?

Wiley

Re: Miter saw question.

#15

Re: Question about Langdon miter saw

Marv

Wiley,

Yes, Disston made the saws for the Millers Falls Langdon Miter Box. Langdon is the name of the inventor. Other saw maker's saws will also fit the Langdon box.

Odd thing about miter saws....the blade dimension is measured from the toe to the end of the blade that's inside the handle, not the tooth edge as are all other saw. So when you see a blade size in a Disston catalog, the tooth edge will be shorter than the dimension shown in the saw description. When you see an eBay auction, the seller will usually specify the length of the tooth edge.

Marv

Re: Miter saw question.

#16

Re: Question about Langdon miter saw

Bill Houghton, Sebastopol, CA

Disston seems to have made saws for a lot of the companies making miter boxes. My Goodell-Pratt boxes came with Disston saws, as did my Langdon Acme. I'm not sure whether Millers Falls owned Goodell-Pratt at the time my box was made or not, so this may be less meaningful than if they'd been separate companies.

Actually, wandering off topic, it appears that Disston was busy making lots of hardened sheet steel products. I picked up a Stanley No. 81 scraper a year or so ago, and it came with a Disston scraper blade, something of a surprise when I took it apart. I presume that this was an aftermarket replacement for the stock blade - a little as if Lee Valley or Ron Hock were one of the larger tool makers.

Re: Miter saw question.

#17

I was wondering about that, too,

Bruce, a MN Galoot

because there is a Disston Cast Steel in my Langdon Acme. It's a little on the dirty side, but I'll try to clean it up and post some stuff later this week.

Re: Miter saw question.

#18

Moses Yoder

Re: Shop Decorations

Moses Yoder

I have a 36" pike mounted in my shop; my wife threw it out of the house ;) I caught it on a trip to Canada about 15 years ago, with a spinner I made on a rod that I built. I would cast the large spinner (about 4" blade) up towards the weed beds and retrieve them just under the surface so I could see the pike hit it. This pike hit when I was fishing in a channel and cast between 2 weed beds and started retrieving just under the surface; I could see the flash of the spinner and suddenly this huge head came up and grabbed it; it was quite an experience.