Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

A Shaker table for Mother's Day

Posts

A Shaker table for Mother's Day

#1

A Shaker table for Mother's Day

Derek Cohen (in Perth, Australia)

The Shaker-style table is complete, just in time for Mother�s Day.

Lynndy wanted a table for her sewing machine. It needed to be high enough to sit at using a diningroom chair, large enough for the sewing machine, and compact enough to fit into a corner of a small spare room. The Shakers actually designed a sewing table, however I don�t think that they had in mind the use of a machine with it! :)

The overall dimensions are 30� high, 33� wide and 19� deep.

The wood is Jarrah, all of it salvaged from roof trusses and old floor boards, all very well seasoned, dry and almost brittle, which made it a challenge to handplane and turn on the lathe. The wood also was filled with voids where gum had dried and fallen out. I filled a few with black-tinted epoxy, but left most alone.

The finish is Organoil hard burnishing oil and wax, both buffed. It has left a soft, natural feel and look.

Thanks to all for their critiques and input. I took the advice of a few, especially Adam Cherubini, to lower the apron by adding a cockbead. A friend came by and said, �Mmm � that sits well with the bead on the legs (below the pommel)�. So it was meant to be. And to Pam, I think that you are right � this is a formal Shaker table :)



Before the top was oiled the colour match of the boards appeared better than this. The outer boards are a very attractive fiddleback Jarrah, which is difficult to see here ..


The ends are pinned breadboards ..


Here is a look at the detail around the pommel ..


And the turned legs (which do taper at the top and bottom) ..


I mentioned earlier that the wood was all salvage. From the outside all looks nice and clean, but when you look underneath and inside you will see that the boards are all different thicknesses � I used what I could the best way possible �





Thanks for looking ..

Regards from Perth

Derek

Re: A Shaker table for Mother's Day

#2

It looks so great in its place!

Wiley Horne--So. Calif.

Is the floor jarrah too? Someone walking in would think the table was made the same time as the floor was laid, out of the same material. The room itself looks Shaker, so the table is a perfect match to its surrounds.

Wiley

Re: A Shaker table for Mother's Day

#3

Re: It looks so great in its place!

Derek Cohen (in Perth, Australia)

Thanks for the kind words Wiley.

Yes the floor is Jarrah, but this is not the resting place for the table - it was just easier to photograph it there.

Regards from Perth

Derek

Re: A Shaker table for Mother's Day

#5

Re: A Shaker table for Mother's Day

Bill Houghton, Sebastopol, CA

The pins on the legs make visual sense with the pins on the breadboard ends. There's a kind of "see, when we have a joint we pin it" effect.

Adam will, I'm sure, applaud your use of the wood as you found its thickness. Why spend time on something that's not visible?

Re: A Shaker table for Mother's Day

#6

Re: A Shaker table for Mother's Day

Bruce, a MN Galoot

I like the style and the work. Not sure that it's good form to have a deadline and meet it, though ;)

The pins work - not much else needs to be said. I'm in the throes of finishing a smaller table with 1 drawer that will be a wedding gift for our goddaughter.

Nice job as usual, Derek.

Re: A Shaker table for Mother's Day

#8

Re: ... in its place ....

Wiley Horne--So. Calif.

Derek,

It really belongs there as well! And the light through the window will bring out the complexity of the grain. Plus let her see!

One particular sewing machine is deeply etched into my memory--I can recall my Grandmother sewing at her Singer treadle machine beneath an east window in the morning, with the sunlight streaming in and the motes of dust floating in the light. Trying to recall if she ever got it motorized.

Wiley

Re: A Shaker table for Mother's Day

#9

Re: A Shaker table for Mother's Day

Marv

Derek,

Simple lines, easy on the eyes. I like the different shades of the wood. Gives it character. The pegs adds to, not a detraction at all.

It's always most rewarding to take something that is crappy looking and bring out the beauty thats hiding inside.

Marv

Re: A Shaker table for Mother's Day

#10

There IS a sense of triumph

Bruce, a MN Galoot

in taking discarded wood, pallet wood, someone's firewood stash and turning it into a decent object, isn't there! I made a Japanese style tool box this winter from the discarded wood that held a Chrysler transmission. Inspiration came solely from Bob Le's post.