Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

shop expansion

Posts

shop expansion

#1

shop expansion

Catharine Kennedy

For some reason, I find I have more tools and interests than I hade 25 years ago when I built my shop, so I'm expanding it somewhat- my question is, what do you folks do with your walls- sheet rock, plywood, bare studs????

Thanks- :D

Re: shop expansion

#2

Solid(reclaimed) wood or plywood

Bob Hackett

Or OSB at the very least.That way you have very durable walls and you can hang just about anything anywhere and not have to worry about finding or spanning studs.

Then again,my projects are usually larger scale in both wood and metal and I tend to be the proverbial "bull in a china shop" during the early phases so over-engineering pays dividends with me and my approach.

BTW-I painted the walls and overhead white as per my brother`s suggestion and found it reduced my need for lights,made the shop look bigger and made it easier to find things.

Re: shop expansion

#3

Not there yet, but

Bruce, a MN Galoot

the walls in my shop are going to be plywood or OSB, painted white. Sheetrock on the ceiling, skylight, plus a solar collector heater on the south wall.

Re: shop expansion

#4

Re: shop expansion

Pam Niedermayer - Austin, TX

I enjoy viewing the structure of buildings and other constructions, such as motorcycles and cars. To that end, I only overlay the structure with plywood (I plan to make an Inomoto-san Japanese plywood area for holding chisels and other tools) where needed. I also make liberal use of magnetic bars, which only have to span16-24" OC.

Pam

Re: shop expansion

#5

Jack Guzman from Maine

wood

Jack Guzman from Maine

Sheetrock in my opinion is useless in a woodworking shop.Except maybe as a backdrop for shop photos. You can't attach anything to it and if you bump into it you put holes in it. I like white pine boards everywhere.I buy knot filled,#4 grade boards,very cheap. You can put a nail anywhere you want to hang something.Attaching brackets,hooks,cabinets or whatever is simple.Bare or finished,pine is pleasing to look at.If pine is not native to your area, whatever wood is cheapest is the best choice for shop walls.---Jack

Re: shop expansion

#6

Re: wood

wilbur

"I like white pine boards everywhere.I buy knot filled,#4 grade boards,very cheap. You can put a nail anywhere you want to hang something."

Except if you want to put a nail in the middle of a knot, I guess. ;)

I have bare 2x4's attached to cinder block walls in my basement shop, and have been screwing boards to the 2x4's to provide a place to attach home made tool racks as needed. Sometimes I just attach the rack directly to the 2x4's.

Re: shop expansion

#7

Re: shop expansion

GregForster

I would go with a combination, use sheetrock in the handtool area. Painted white or off-white it really brightens up the work area.

Where the walls may take some bumping/banging, either Pam's suggestion of plywood or Jack's use of lumber to cover the walls.

I did a project where I used rough-sawn random 6-10" hemlock. I had an Amish

saw mill plane one face for thickness and run a rabbet along both edges.

The vertically applied boards look great and provide durability.

Included a couple photos of my handtool only shop (7'x12'- in progress) with sheet rock walls, 100% skimmed to give a plaster look/feel. The ceiling is sloped as the shop is in the top of a barn with gambrel roof. Power tools stay downstairs on the concrete floor.

Re: shop expansion

#8

Here

Dan Donaldson

If I did that here, I would be viewing lots of fiberglass insulation or freezing to death ;)

Re: shop expansion

#9

Re: Here

Pam Niedermayer - Austin, TX

Well, you could always replicate the structure as the interior decoration. :)

Pam

Re: shop expansion

#10

Re: shop expansion

Pam Niedermayer - Austin, TX

This lighting thing is something of an issue for me, too; so I think I'll try painting the interior structure. Thanks.

Pam

Re: shop expansion

#11

that looks like a great shop space!

Bruce, a MN Galoot

Re: shop expansion

#12

Smallest Shop

R.J. Whelan

Greg,

You almost beat me for smallest shop; I got you by just 3 feet - 81 square feet to your 84.

Of course when I read about woodworker who do their work at a kitchen table, or on a balcony I feel positively blessed with space.

RJ

Re: shop expansion

#13

Re: shop expansion

Wiley Horne--So. Calif.

Beautiful space, Greg. Has a Shaker way about it, to my eye, with the wood trim on white, and exposed beams.

Thanks for sharing!

Wiley

Re: shop expansion

#14

Re: shop expansion

GregForster

Thanks. Actually, since its in a "hayloft" there's 12' headroom above the workshop ceiling. I doubled 2x8s for ceiling joists and decked with plywood to create a 7'x12'x12' storage area above. Then I wrapped the ceiling joists with rough sawn lumber to give the appearance of beams. If I did it again, I'd frame a flush ceiling and then put in some "dummy" beams at 30" on center. These look to close together for their size. But its done and I'm not goin' to move them.

If only furniture building was that easy for me, but it's not.

Re: shop expansion

#15

Never had much of a problem with sheetrock

John in NM

Its about the cheapest wall covering there is, dings are really easy to patch - I've rarely had anything bigger than a corner of wood block shaped dent - and frankly, its just so easy to find the studs and hang things from them that I've never understood the plywood everywhere route. If I could go to a local sawmill and buy pallet grade wood I might have a different viewpoint, but out here sawmills are few and far between, and the one I know of within 100 miles is more expensive than a commercial yard with a rail spur :D

We've almost got the stem wall done for the shop/guest room building that I hope will be done next fall. I only have one interior wall planned, which will be drywalled. Exterior walls are straw bale, so they get thick plaster which requires a cold chisel to dent.

Re: shop expansion

#16

Re: shop expansion

ThomD

I used sheetrock, and taped the joints to a 4-5 finish, then paint etc... I ran a high french cleat all around the shop so I could hang racks anywhere. If you don't know drywall work, consider using Myron Fergusens tape. The key there is a consistant approach, and finishing each step in one application.

Drywall is fire resistant which is a big plus over plywood.

If the local culture supplied the materials, I would either use a solid drywall where all the sheets are uniform material and undentable, or a would skimcoat plaster. Unfortunately those products aren't available locally.